31
BEFORE YOU TAKE OFF
Refer to and follow all safety precautions mentioned in the “General Instructions and Guidelines for use”
section of this manual.
Check that your aircraft is ready for flight with no loose screws or fittings (pay special attention to the
propellers) insert a battery into the battery bay and use the provided strap to secure the battery in place.
Refer to and follow all safety precautions mentioned in the “Safety Advice” and “General Instructions
and Guidelines for Use” sections of this manual
Make sure that your transmitter controls are all in their correct positions and that the throttle is off.
Ensure that you always turn on your transmitter before connecting the Lipo battery power. After flying
make sure that once the motors have stopped turning, you always disconnect your aircraft battery
before turning off your Transmitter.
MOTOR ARMING AND TAKING OFF
You arm your motors by using the sequence that you recorded during the transmitter setup stage of this
manual. Make sure that the throttle control is at its lowest position and then push the other control to
the Motor Arming position.
To stop the motors, you should have the throttle stick at its lowest position and you push the other stick
in the opposite direction to the one you used to Arm the motors
7
- Now you can see your signal power level on your Link9 radio
Signal power level:
Lo
id
High
HOW TO CONNECT & BIND (with Sky-Hero LINK9 RX & TX)
FLIGHT MODES
1. STABILIZED SUPER SOFT:
(ATTITUDE MODE) - Switch 3 in UP postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is VERY LIMITED.
2. STABILIZED SOFT:
(ATTITUDE MODE) - Switch 3 in MIDDLE postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is LIMITED.
3. RATE:
(RATITUDE MODE) - Switch 3 in DOWN postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is UNLIMITED.
Then:
• Turn your Link9 on
• Plug your lipo in your model
• Push and hold the bind button until the Led start blinking
• Push again the button again until it starts blinking blue (meaning S.BUS-
mode)
• Once the Led turns solid blue, it’s bound
BASIC COMMANDS
See hereunder how to control your Anakin.
Throttle:
it cannot hold the central position when released.
Roll:
it can return to the central position when released.
Pitch:
it can return to the central position when released
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 1]
Pitch:
it can return to the central position when released
Roll:
it can return to the central position when released.
Throttle:
it cannot hold the central position when released.
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 2]
With Link9. you have to connect with the cable as shown on the picture.
(Yellow cable is not used)
7
- Now you can see your signal power level on your Link9 radio
Signal power level:
Lo
id
High
HOW TO CONNECT & BIND (with Sky-Hero LINK9 RX & TX)
FLIGHT MODES
1. STABILIZED SUPER SOFT:
(ATTITUDE MODE) - Switch 3 in UP postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is VERY LIMITED.
2. STABILIZED SOFT:
(ATTITUDE MODE) - Switch 3 in MIDDLE postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is LIMITED.
3. RATE:
(RATITUDE MODE) - Switch 3 in DOWN postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is UNLIMITED.
Then:
• Turn your Link9 on
• Plug your lipo in your model
• Push and hold the bind button until the Led start blinking
• Push again the button again until it starts blinking blue (meaning S.BUS-
mode)
• Once the Led turns solid blue, it’s bound
BASIC COMMANDS
See hereunder how to control your Anakin.
Throttle:
it cannot hold the central position when released.
Roll:
it can return to the central position when released.
Pitch:
it can return to the central position when released
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 1]
Pitch:
it can return to the central position when released
Roll:
it can return to the central position when released.
Throttle:
it cannot hold the central position when released.
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 2]
With Link9. you have to connect with the cable as shown on the picture.
(Yellow cable is not used)
7
- Now you can see your signal power level on your Link9 radio
Signal power level:
Lo
id
High
HOW TO CONNECT & BIND (with Sky-Hero LINK9 RX & TX)
FLIGHT MODES
1. STABILIZED SUPER SOFT:
(ATTITUDE MODE) - Switch 3 in UP postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is VERY LIMITED.
2. STABILIZED SOFT:
(ATTITUDE MODE) - Switch 3 in MIDDLE postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is LIMITED.
3. RATE:
(RATITUDE MODE) - Switch 3 in DOWN postion
Anakin comes back to a flat position when LEFT STICK is back to neutral position - The maximal angle of the drone is UNLIMITED.
Then:
• Turn your Link9 on
• Plug your lipo in your model
• Push and hold the bind button until the Led start blinking
• Push again the button again until it starts blinking blue (meaning S.BUS-
mode)
• Once the Led turns solid blue, it’s bound
BASIC COMMANDS
See hereunder how to control your Anakin.
Throttle:
it cannot hold the central position when released.
Roll:
it can return to the central position when released.
Pitch:
it can return to the central position when released
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 1]
Pitch:
it can return to the central position when released
Roll:
it can return to the central position when released.
Throttle:
it cannot hold the central position when released.
Yaw:
it can return to the central position when released.
LEFT STICK
RIGHT STICK
[MODE 2]
With Link9. you have to connect with the cable as shown on the picture.
(Yellow cable is not used)
The notes below are for a transmitter setup as Mode 2 (for Mode 1 replace “RIGHT” with “LEFT”)
