background image

Board Layout

3-4

ADSP-2181 EZ-KIT Lite Evaluation System Manual

Socketed Memory

The socketed EPROM provides up to 128k x 8 bits of program storage 
that can be loaded by the ADSP-2181 processor when it is programmed to 
boot from the socketed EPROM. After the ADSP-2181 processor is reset, 
the BDMA feature is used to load the first 32 words of program memory 
from the byte memory space. Program execution is held off until all 32 
words are loaded. Refer to the ADSP-218x DSP Hardware Reference and 
the ADSP-2181 DSP Microcomputer Data Sheet for more information on 
program booting and processor modes.

User LEDs

The 

D1

 LED is a red light emitting diode, which is controlled by the 

FL1

 

output of the ADSP-2181 processor. Software can control the state of this 
indicator by writing to an internal register.

The 

D2

 LED is a green light emitting diode, which is on whenever the 

board has power.

Switches

The

 S1

 switch is the reset push button switch. Pushing this button causes 

the ADSP-2181 processor and the AD1847 codec to enter the hardware 
reset state and remain there until it is released. The switch outputs are 
de-bounced electronically to prevent multiple transitions due to mechani-
cal contact bounce.

The 

S2

 switch is the interrupt push button switch. Pushing this button 

causes the ADSP-2181 to receive an 

IRQE

 interrupt input. The processor 

then executes the current 

IRQE

 interrupt handler software if the interrupt 

is enabled and the 

IRQE

 interrupt vector is in place. The interrupt switch 

output is de-bounced electronically to prevent multiple interrupts due to 
mechanical contact bounce.

Summary of Contents for ADSP-2181







































































Reviews: