background image

 

 

7

 

Limited Warranty 

 
 
1. 

The equipment manufactured by Analytic Systems Ware (1993) Ltd. (the “Warrantor”) is 
warranted to be free from defects in workmanship and materials under normal use and 
service. This warranty is in effect for 3 years from the date of purchase by the user (the 
“Purchaser”). 

 
2. 

In case any part of the equipment proves to be defective, the Purchaser should do the 
following: 
a) 

Prepare a written statement of the nature of the defect to the best of the Purchasers 
knowledge, and include the date of purchase, the place of purchase, and the 
Purchasers name, address and telephone number. 

b) 

Call Analytic Systems at 1-800-668-3884 or 604-543-7378 and request a return 
material authorization number (RMA). 

c) 

Return the defective part or unit along with the statement at the Purchasers expense to 
the Warrantor; Analytic Systems Ware (1993) Ltd., #207 12448 82nd Ave., Surrey, 
B.C., V3W 3E9, Canada. 

 
3. 

If upon the Warrantor’s examination the defect proves to be the result of defective material or 
workmanship, the equipment will be repaired or replaced at the Warrantor’s option without 
charge, and returned to the Purchaser at the Warrantor’s expense. 

 
4. 

No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is 
unable to remedy the defect after having a reasonable number of opportunities to do so. 

 
5. 

Warranty service shall be performed only by the Warrantor. Any attempt to remedy the defect 
by anyone else shall render this warranty void. 

 
6. 

There shall be no warranty for defects or damages caused by faulty installation or hook-up, 
abuse or misuse of the equipment including exposure to excessive heat, salt or fresh water 
spray, or water immersion except for equipment specifically stated to be waterproof. 

 
7. 

No other express warranty is hereby given and there are no warranties which extend beyond 
those described herein. This warranty is expressly in lieu of any other expressed or implied 
warranties, including any implied warranty of merchantability, fitness for the ordinary purposes 
for which such goods are used, or fitness for a particular purpose, or any other obligations on 
the part of the Warrantor or its employees and representatives. 

 
8. 

There shall be no responsibility or liability whatsoever on the part of the Warrantor or its 
employees and representatives for injury to any person or persons, or damage to property, or 
loss of income or profit, or any other consequential or resulting damage which may be claimed 
to have been incurred through the use or sale of the equipment, including any possible failure 
of malfunction of the equipment, or part thereof. 

 
9. 

The Warrantor assumes no liability for incidental or consequential damages of any kind. 

 

Summary of Contents for PWS610 Series









Reviews: