background image

Yes, you may install popular open source software for home automation on your Raspberry Pi such as 

Home Assistant

 or 

OpenHAB 2

 and integrate ANAVI Infrared

pHAT.

Is ANAVI Infrared pHAT software free and open source?

Is ANAVI Infrared pHAT software free and open source?

Yes, the official ANAVI Infrared pHAT software is free and open source. The examples are available under MIT license and the rest is available under GPLv3. Please
contact us if you are working on a commercial product and you would like to use the software under alternative commercial license.

CHAPTER 7: Revision History

CHAPTER 7: Revision History

Document Revision

Document Revision

Date

Date

Changes

Changes

Modified pages

Modified pages

Author

Author

15 February 2017

Initial manual release

All

Leon Anavi

16 September
2017

Update for Raspbian Stretch

All

Leon Anavi

08 July 2019

Update for Raspbian Buster

All

Leon Anavi

ANAVI Infrared pHAT Revision

ANAVI Infrared pHAT Revision

Revision

Revision

Notable changes

Notable changes

1.0

First version

See Also

See Also

For more information please visit 

anavi.technology

 and our 

GitHub repositories

. If you have any questions or enquiries please contact us through 

Facebook

, 

Twitter

 or

email

.

Summary of Contents for Infrared pHAT











Reviews: