background image

ANCHEER

1

Thank you for choosing our products.

To ensure your safety and health, we encourage you to read this manual thoroughly before 
you assemble the bike and take the first ride.Safe and effective use can only be assured if 
the equipment is assembled, maintained, and used properly. More importantly, this will 
offer you a general understanding and get the most out of your bike.Please check your 
electric bike before every ride, especially when traveling long distances.

This manual is intended as a general guide to your new e-bike. For technical support, 
including repair information, please consult your dealer.

Things to know before use

Do not use the product before carefully reading the instructions from this manual and 
understanding the performance of the item;

Don't lend this product to people who can't operate it, so as not to cause harm; if you 
lend the bike, please let the user follow instructions, it could help to decrease the risk 
of accident;

The E-bike cannot be used as off-road vehicles or used for extreme bicycle sports; when 
riding the bicycle, please wear a safety helmet and protective gear. It is forbidden to ride 
with one hand;

Please abide by the traffic rules and prohibit riding on motorized lanes and roads with 
multiple pedestrians;

Carry people or objects in accordance with the requirements of laws and regulations, 
and do not park in the building's lobby, evacuation stairs, walkways, and safe 
entrances and exits;

It is recommended to charge and park in an outdoor dedicated parking hall, while 
avoiding rain; when charging, keep away from combustibles, and the charging time 
should not be too long;

For safety reasons, please do not change the default speed setting of the electric 
bicycle and do not exceed speed limit in accordance with the traffic rule. Riding on 
non-motorized lanes, downhills and paved roads not exceeding 15km/h;

When adjusting the handlebar or saddle, please be careful not to exceed the safety 
line markings on the handlebar and saddle;

Please check the tire pressure before riding, the recommended tire pressure is 35-
45PSI;

Please check the power circuit, lighting circuit, etc. before riding;

Safety Instruction

Summary of Contents for MYT-26






















Reviews: