background image

30’

 CLASSIC FRAME TENTS  

|

  

ASSEMBLY INSTRUCTIONS

IMPORTANT: Cross Bracing Tubing and Fittings are supplied with the tent framing and must first be in place 
before raising the tent on the legs. 

8.

 For stability and to prevent frame bowing, 

solid interior bracing using 14’4” x 2” 
Cross Brace Tubing and Fittings

 need 

to be installed between each opposing 

16’1/4” Mid-Rafters. Start at one end along 

the longer side and install as many cross 

braces as there are mid-rafters.

CROSS BRACING

 COVER ATTACHMENT

  9.

 Roll out a large drop cloth next to the assembled frame to protect the cover from dirt and abrasion. 

10.

 Lay out two-piece covers with lace edges together and top side up. 

Matching centerlines, start in the center by pushing the first lacing 

loop up through the corresponding grommet. 

(See diagram) Continue 

lacing process and tie off last long lacing loop. Cover lacing with 

protective flap and secure the hook-n-loop closure. Repeat lacing 

procedure on the opposite side.

11.

 Loosely pull the cover over the frame. Check the corners, hip areas and crowns to make sure the cover is 

positioned correctly on the frame. Temporarily strap the cover at the corners and side (if required) of the frame 

to keep any wind from catching the cover.

 ADDING LEGS AND LIFTING

12.

 Lay out the (7’-9’) Adjustable Legs at each Corner Fitting and at each Mid-Rafter Fitting location. Leave 

the adjustable Legs at the shortest length. Starting at the two corners of the longer side of the frame, two 

installers should lift the corner Legs to their vertical position. Then together lift the entire side of the tent frame 

and insert the Corner Fittings onto the corner Legs until the snap button engages.

 (Do not lift one corner at 

time; lift the entire side of the tent.)

 Insert Legs into the side Mid-Rafter Fittings along the same elevated side 

until the snap button engages.

13.

 Repeat the above procedure for inserting the Legs on the opposite side of the frame. Then insert Legs into the 

side Mid-Rafter Fittings along the shorter side until the snap button engages.

Summary of Contents for ETI 30’CLASSIC FRAME TENTS









Reviews: