background image

6

Directions for Squaring the Tent

(see the diagram above)

1.  Locate the four primary corners.

a.  Using a tape measure, mark Points A & B (the width of the pavil-
ion fi rst.

b.  Using one tape measure,  start from point B and measure the 
length of the tent.
c. Using a second tape measure, start from point A and measure the 
diagonal.

d.  Mark the point at which these two tapes intersect.  (Point C)  This 
will square the tent.

e.  Using the same process, mark point D.

2.  Locate points for inter-
mediate uprights. 
 

a.  Using a tape mea-

sure running from points A 
to B, mark for end uprights 
(only on frames over 20’ 
projection).  
b.  Using a tape measure 
running from points B to 
C (or A to D) mark for side 
uprights according to your 
particular pavilion. 

These markings will be 
your guideline for tent 
layout.

PLAN VIEW OF 3 BAY STRUCTURE

(22’ Projection shown)

Upright centered on 
end required only 
on structures above 
20’ projection.
(2) Hole Base Plate 
required at this 
position only.

LAYOUT DIMENSIONS

Pavilion Size

“A” Dimension

“B” Diagonal Dim.

12’ Projection x 30’

12’-6 15/16”

32’-6 3/8”

14’ Projection x 30’

14’-6 15/16”

33’-4 1/4”

16’ Projection x 30’

16’-6 15/16”

34’-3 5/16”

18’ Projection x 30’

18’-6 15/16”

35’-3 7/16”

20’ Projection x 30’

20’-6 15/16”

36’-4 9/16”

22’ Projection x 30’

22’-6 15/16”

37’-6 9/16”

24’ Projection x 30’

24’-6 15/16”

38’-9 3/8”

4-Hole base plate 
(typ.)

To fi nd a diagonal measurement not listed here, use 
this formula:  width² + length² = diagonal²

Point A

BACK OF PAVILION

Point D

Point C

“B” DIMENSION - SEE 

TABLE

DIAGONAL

 IS MEASURED 

TO

 CENTER 

BACK 

AND CENTER FRONT

 OF BASE-

PLA

TES 

AS SHOWN IN DET

AILS.

“A” DIMENSION - SEE 

T

ABLE

MEASURED FROM OUTSIDE OF BASE-

PLA

TE 

T

O

 OUTSIDE OF BASEPLA

TE.

1

1’-1 7/8” for 22’

 Projection

12’-1 7/8” for 24’

 Projection

1

1’-5 1/16” for 22’

 Projection

12’-5 1/16” for 24’

 Projection

FRONT OF PAVILION

Point B

30’-0”

10’-0”

10’-0”

10’-0”

C

L Front and Back 

Uprights

C

L Front and Back 

Uprights

Standard 4-hole Base Plate

2-Hole Base Plate for End Uprights

C

L Uprights

C

L Uprights

Summary of Contents for Navi-Trac LT/CS

















Reviews: