background image

                                                                                                   

  

4

From atmosphere 

To atmosphere 

Extract from dwelling

Supply to dwelling 

2. PRODUCT  DESCRIPTION 

 

The DC Heat Recovery MVHR unit is a mechanical ventilation/heat recovery (MVHR) unit for domestic and 
commercial applications. It is designed for connection to 125mm-diameter ducting. 
The unit’s two fans and heat exchanger arrangement simultaneously supply and extract air while transferring heat 
from the stale exhaust airflow to the fresh intake airflow. This provides up to 91% heat recovery from the stale 
extracted air.  
Separation of the exhaust airflow and intake airflow is maintained throughout the unit. 
The fan motors have maintenance free, self lubricating long life bearings and are fitted with thermal overload 
protection, which in the event of a fault causing a motor to overheat will cut off the electrical supply to that motor. If this 
occurs, isolate the unit, check for any obstructions, leave the unit for a short time for the motor to cool before 
reconnecting the power supply. If the fault reoccurs, isolate the power supply and call a service engineer. 
The fans in this unit are low energy EC motors with a constant (100% adjustable) air volume. 
 
 
The EU3 filters in the unit ensure that the fresh supply air is clean as it enters the home. Also the extract air from the 
property is filtered to protect the heat exchanger from unwanted contamination.  Check filters regularly and clean if 
necessary.   
The unit is delivered complete with a mounting plate, fitting instructions, fixing kit and a condensation discharge fitting.  
 

Left Hand configuration shown 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Condensate exit on  
Atmosphere side 
(See connecting the 
condensate drain section). 

Front Panel 

Filter access covers 

Filters 

Summary of Contents for 443423















Reviews: