background image

3

PRODUCT MANUAL

68/72ST Above Deck Compact Motor

Read All Safety Notices and Product Manuals

Do not install or operate this winch before reading and fully understanding the contents of this Safety Notice Sheet and the 

Product Manual.

Stay Alert When Operating

Andersen winches are very powerful and have the potential to cause significant damage and/or serious injury if used 

improperly or without due caution and vigilance.

Operators Must be Trained

Help prevent significant damage and/or serious injury by ensuring any person operating a winch has a thorough 

understanding of its proper operation and is aware of the potential hazards involved. As a minimum, all winch operators 

must read and understand this Safety Notice Sheet and the Product Manual.

Particular attention is drawn to the following points:

• 

Children and others not qualified to operate an electric winch must be kept at a safe distance from the winch and any 

rigging or fittings that are under load.

• 

Long hair and/or loose clothing must be tied back to avoid being caught in the winch.

• 

In the event of a rope override or other fault, stop the winch and turn off power before attempting to resolve the 

problem.

Avoid Accidental Operation

Always turn off power to the winch at the circuit breaker and remove winch handles when not in use to help avoid 

unsupervised or unintentional operation. Failure to do so could result in significant damage and/or serious injury.

Maintenance

Turn off power to the winch before performing any maintenance or service tasks. Failure to do so could result in significant 

damage and/or serious injury.

Lifting Operations

The winch must not be operated with the rope in the self tailer when used in any kind of lifting operation. Any lifting 

operations should be conducted by two persons in order to maintain constant visual contact with the object being lifted. 

Furthermore the self tailer must not be used as a cleat for a rope used to lift or suspend any object. The rope must be 

secured properly by tying off, or leading to a suitable fitting such as a cleat or bollard.

Failure to observe these precautions could result in serious injury  

or death.

DO NOT DISCARD

SAFETY NOTICES

Summary of Contents for Compact Motor 68/72ST























Reviews: