a )Overload And Idle Running Is Forbidden During Use.
b)The Milling Cup Is Only Suitable For Processing Dry Food Into
Power. Don’t Pour Any Liquid Into It. The Recommended Quantity
Of Food Put In The Cup Is 1/3 To 2/3 Of The Volume Of The Cup.
c ) Water Of Edible Oil Must Be Remained In The Filter Screen So
As To Ensure A Running Balance.
d) A Certain Volume Of Heat Water And Several Drops Of Food
Cleaner May Be Added In The Water When The Mixing And Minc-
ing Cups Are To Be Washed. They Can Be Cleaned Through An
Idle Running By Switching On The Power Button Or Quick Clean-
ing Button For 10 Seconds. Also, They Can Be Cleaned In Water
By A Brush.
e) The Device Should Be Stored In A Dry And Ventilated Place
When They Are Not In Use.
f) The Blade Is Very Sharp, At Cleaning With Replace The Agitation
Knife Hour Must Look Out.
g) If The Supply Cord Is Damaged, It Must Be Replaced By The
Manufacturer Or Its Service Agent Or A Similarly
Qualified
Person
In Order To Avoid A Hazard.
x
(3)Combination With Mincing Cup And Usage
a) Put The Main Engine A On The Flat Top Of A Table.
b) Amount The Mincing Cup X To The Main Engine. Press Down The Cup And Screw It Counter-
clockwise So As To Get The Cramp On The Cup Firmly Locked At The Cramping Position Of Main
Engine.
c) Cut The Meat Into Small Pieces (Get Rid Of Skins, Boned And Tendons) And But Them Into The
Mincing Cup. Put On The Cover Of Mincing Cup And Get It Pressed Tightly.
d) Press The Mincing Cup By One Hand And Switch On The Power By Another Hand To Start The
Mincing Operation.
Caution
:
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
5
R
P
M
Q
A
O
Continue Work Time : Don’t Exceed 1 Minute
The Turning Of Electric Appliances Is Soon:
About 12000 Rpm.
2 Main technical parameters
1.Rated Voltage: 220-240V~
2 Rated Frequency: 50Hz
3. Rated Power: 500W
4. Protection Class II
3 Combination of juicer and method for use
1. Put The Engine A On A Table
2. Put The Juice-Residue Separating Slot Q Onto The Engine And Tighten It
Counterclockwise.
3. Amount The Filter P To The Driving Gear.
4. Put The Transparent Cover O Onto The Separating Slot Q And Then Get The
Safety Buckle Engaged In And Make The Separating Slot Q Be Firmly Fixed
With The Transparent Cover O.
5. Let The Juicer Have An Idle Operation For Five Seconds Before Putting It Into
Work Operation, Which May Prolong The Service Life Of This Product.
6. Get Rid Of Fruit Skin And Slice Up The Fruit Properly. Put The Sliced Fruit
Into Feeding Port And Push Them Into The Juicer By Feeding Bar.
7. The Juicer Can Be Disassembled Only After The Running Of Motor Has Com-
pletely Stopped.
Caution:
1. The Power Switch Must Be Turned On Prior To Feeding Sliced Foods. Don’t
Use This Juicer For Processing Those Fruits That They Are Extremely Soft And
The Separation Of Juice From Residues Is Difficult.
2. The Power Must Be Turned Off Immediately If The Motor Doesn’t Run After
The Switch Has Been Turned On. It Can Be Restarted Only After The Trouble
Has Been Found Out And Remedied.
3. When It Is Used For Pressing Sugarcane, The Sugarcane Must Be Cut Into
Proper Pieces With Proper Thickness. During Operation, The Sugarcane Pieces
Should Be Pressed Down While Being Rotated.
4. When Operation Is Finished, All Parts Or Components Must Be Cleaned Up
And Assembled To Have A Dewater Operation.
5. The Main Engine Mustn’t Be Cleaned In Water Or Rinsed With Water. It
Should Be Cleaned By Wet Cloth.
6. Don’t Operate The Juice By Children.
7. Don’t Use The Appliance If The Rotating Sieve Is Damaged
FOOD
PROCESSOR
COMBINED MULTIFUNCTION
2
A
