Anglerfish Creative Lighting TRIGGER V3.0 User Manual Download

Page: 14 / 15

p.10

Anglerﬁsh Crea�ve Ligh�ng

Anglerﬁsh Trigger V

2.0

Speci�ication

Parameters

Value

Opera�ng Temperature

0 -

40°C

Batery Type, Capacity

CR2,

700-850

mAh

Sleep Mode Opera�ng Time

400

days (full batery)

On Mode

Opera�ng Time

~60

hrs (blue mode)

Weight

, Dry

(Submerged)

~100

grams (

-30

grams)

Compliance

Anglerﬁsh Trigger:

Anglerﬁsh Trigger is constructed from

electrical

components and parts that are RoHS compliant.

Anglerﬁsh is a lead

fee product.

This electronic product should not be mixed with
general household waste. The correct disposal of this

product will help prevent any poten�al nega�ve eﬀect to the
environment. For disposal please take this product to a
designated electronic waste recycling or disposal area.

Summary of Contents for TRIGGER V3.0
















Search results

Summary of Contents for TRIGGER V3.0

Reviews:

Related manuals for TRIGGER V3.0

Brands by name

Popular brands

Anglerfish Creative Lighting TRIGGER V3.0, User Manual

Search results

Summary of Contents for TRIGGER V3.0

Reviews:

Related manuals for TRIGGER V3.0

Brands by name

Popular brands