background image

 

 
 
 

DCU20

 User Manual rev. 19 

Page 6/29 

 

2  Features and benefits 

The main features are: 

  Integrated 

battery charger

 for multi-chemistry batteries with charging current up to 5A. 

  Automatic sensing of 

input voltage

load current

 and 

battery current

  Protections  against 

battery  reverse  polarity

  connection  and 

over  current

  when  operating 

from the battery. 

  Battery 

health  monitoring

”  system:  measuring  battery 

internal  resistance

,  battery 

temperature

 and providing a 

Coulomb counter

  User settable 

maximum backup time

  Remote input to 

inhibit

 the UPS function. 

  Connection of a battery 

thermal sensor

 (optional). 

 

Integrated data logger

 with 

time stamp

: all events / errors are logged in the internal memory 

and downloadable through the USB interface. 

 

Automatic PC shutdown/restart function (see §3.3)

 

 
Embedded user interface: 

 

4  buttons

  and 

1  color  graphic  CSTN  LCD

,  Displays  the  set-up,  status,  measures  and 

alarms 

 

Online device configuration

 

USB

 

port

 for remote monitoring and configuration. 

 

Dry contacts 

for status monitoring 

 

POWERMASTER

 PC application: 

  Connection through USB interface. 

  Remote monitoring and configuration. 

  Firmware upgrade. 

  Same functionalities of the embedded user interface with the ease of the PC benefits. 

 

6

DCU20_1680-21539-0006-E-1117

Summary of Contents for nextys DCU20































Reviews: