Anilam 4200T CNC Manual Download

Page: 3 / 31

CNC Motion Setup/Testing Utility

P/N 70000634A - Contents

23-December-05

Introduction ................................................................................................................... 1

Accessing the MST Utility ............................................................................................ 1

Activating the MST Screen ........................................................................................... 2

MST Soft Keys ............................................................................................................... 3

Clearing a Prompt Field or Message (F1) ........................................................................................... 4

Selecting an Axis................................................................................................................................. 4

Entering a Password ........................................................................................................................... 4

Checking Axis Resolution (F2) ............................................................................................................ 5

Detecting the Index Pulse (F3)............................................................................................................ 6

Canceling the Active MDI or Test Command ...................................................................................... 6

Activating Manual Data Input Mode (MDI)........................................................................................... 6

Balancing Motion Control Axes ........................................................................................................... 7

Servo Amplifier Test Board ................................................................................................................. 7

Test Board Installation..................................................................................................................... 8

Test Points ...................................................................................................................................... 8

Jumpers........................................................................................................................................... 8

Balancing the DSP

Board (F6) ........................................................................................................... 9

ANILAM Amplifier Parameter Files.................................................................................................... 11

Balancing Servo Amplifier Outputs (F6) ............................................................................................ 11

Setup Parameter Verification......................................................................................................... 11

Motion Setup and Testing (MST)................................................................................................... 14

Amplifier Faults ................................................................................................................................. 16

Tuning (F8)........................................................................................................................................ 16

Saving Final Values .......................................................................................................................... 19

Miscellaneous Tests (F9) .................................................................................................................. 20

CanTest......................................................................................................................................... 20

Save Amp Settings ........................................................................................................................ 22

Amplifier Test Link ......................................................................................................................... 22

Reset Amplifier .............................................................................................................................. 23

BackUp Amp Settings.................................................................................................................... 23

Restore from BackUp .................................................................................................................... 23

Exiting the MST Screen (F10) ........................................................................................................... 23

Setting Up and Tuning the C Axis.............................................................................. 24

Index

...................................................................................................................................... Index-1

Summary of Contents for 4200T CNC
































Search results

Summary of Contents for 4200T CNC

Reviews:

Related manuals for 4200T CNC

Brands by name

Popular brands

Anilam 4200T CNC, Manual

Search results

Summary of Contents for 4200T CNC

Reviews:

Related manuals for 4200T CNC

Brands by name

Popular brands