Nor
can
Jula
be
held
liable
for
any
faults
resulting
from
failure
to
follow
the
installation
and/or
maintenance
instructions.
Upon
receipt
of
this
product,
it
should
be
carefully
examined.
Check
the
vacuum
tubes
carefully
in
accordance
with
the
instructions
in
the
enclosed
installation
instructions.
If
faults
are
detected,
they
must
be
reported
before
using
the
product.
Any
faults
detected
should
otherwise
be
reported
immediately.
Jula
cannot
be
held
liable
for
any
indirect
damage,
i.e.
damage
to
property
other
than
the
product,
personal
injury,
loss
of
property,
loss
of
business,
or
loss
resulting
from
downtime
etc.
Jula’s
responsibility
does
not
cover
compensation
for
any
increased
energy
consumption
caused
by
product
or
installation
faults.
In
the
event
of
a
claim
it
will
be
necessary
to
submit
confirmation
in
writing
that
an
authorised
technician
has
carried
out
the
installation.
Guarantee
or
compensation
claims,
including
ordering
of
service
documents,
should
be
submitted
to
Jula
AB
on
telephone
+46
200
‐
885588.
Do
not
carry
out
any
repairs
on
your
own
initiative,
otherwise
this
will
invalidate
the
guarantee.
GENERAL INFORMATION
Important before installation
Never switch on the power supply before the tubes have been routed and the system modules
have been correctly connected by a technician.
The units are heavy and aluminium splinters/sharp edges can cause cuts on the hands. Bend
your knees when lifting, and wear gloves and safety glasses during the installation.
Read all the operating and installation instructions before starting the installation.
ELECTRICAL
SAFETY
New
installations
and
extensions
to
existing
systems
must
always
be
carried
out
by
an
authorised
installation
engineer.
If
you
have
the
necessary
experience
and
knowledge,
you
may
replace
switches
and
wall
sockets,
fit
plugs,
extension
cords
and
lamp
holders.
If
not,
you
should
contact
an
electrician.
Improper
installation
can
result
in
electric
shock
or
a
fire
hazard.
Important information
The control system with microprocessors includes well-tested and developed software.
Indicators show the status of the machine and make it easy to monitor the system.
The system must be connected to an earthed power outlet (230V/50Hz, 10A). Overvoltage
protection and a residual current device shall be available with a separate minimum 10 A fuse.
In the event of interference or an error code, always start by switching off the solar collector and
disconnecting the power for 5 minutes.
Pull out the plug during thunderstorms. Lightning can damage the drive pack for the solar
collector.
Never use water, detergent, thinner or other cleaners to clean the control unit or drive pack. We
recommend using a dry cloth.
Pull out the plug when maintaining and cleaning the system. Risk of electric shock!
Do not tread on, or place heavy objects over the system units or packaging.
Summary of Contents for 417-031
