background image

 

 

User Manual 

Antari ICE Low Fog Machine 

Congratulations on the purchase of your new 

ANTARI FOG MACHINE. 

 

Introduction   

Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful 

state-of-the-art machine. Prior to use, we suggest that you carefully read all of the 

instructions. By following the suggestions found in this user manual, you can look forward to 

the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.   

 

Please follow these operation, safety and maintenance instructions to 

ensure a long and safe life for your fog machine. 

Cautions   

Risk of electric shock. Disconnect the appliance from the electric supply before 

removing the cover. Note: there are no user serviceable parts inside. 

Danger of electric shock 

♦ Keep this device dry.   
♦ For inside use only. Not designed for outside use.   
♦ For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to 

determine that the unit is installed at the rated voltage.   

♦ Always unplug your ANTARI Fog Machine before filling its tank.   
♦ Keep fog machine upright.   
♦ Turn off or unplug when not in use.   
♦ This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the 

housing, immediately unplug the unit and contact a service technician or your ANTARI 

dealer before using it again.   

♦ No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service 

personnel.   

 

Danger of burns 

♦ For adult use only. Fog machine must be installed out of the reach of children. Never leave 

the unit running unattended.   

♦ Never aim the output nozzle directly at people.   
♦ Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during 

operation.   

♦ Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to 

Summary of Contents for ICE-101











Reviews: