ANTTI E-series Installation Instructions Manual Download | Manualshive

Page: 3 / 15

background image

Antti-Teollisuus Oy

3

408012

06-2018

SHUTTER PLATE, OPERATED BY LINEAR ACTUATOR ..................................................................................... 4

Contents of the package.........................................................................................................................................5

Installation in the E-series elevator.........................................................................................................................6

Attachment of the frame plate (E-model)................................................................................................................ 7

Attachment of the draw support..............................................................................................................................8

Supporting the linear actuatorrod ...........................................................................................................................8

Cutting and attachment of shutter plate rods.......................................................................................................... 9

Connecting the cables to the linear motor ............................................................................................................ 11

LOCATION OF SENSORS ...................................................................................................................................12

GUARANTEE TERMS ..........................................................................................................................................14

EU- Declaration of Conformity ..............................................................................................................................15

Contents

«
1
2
3
4
5
...
»

Summary of Contents for E-series
















Reviews:

No comments

Related manuals for E-series

Brand: RANKO Pages: 61

Brand: Hitachi Pages: 340

Brand: Hitachi Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands