background image

Important Information 

— Please Read Before Use

 

 

-2- 

 

For Veterinary use only 

 

 

Signal words

 

The following signal words are used throughout this manual: 

 

: It indicates a potentially hazardous situation, if not be avoided, could result in death 
or serious injury. 

 

: It indicates a potentially hazardous situation, if not be avoided, may result in minor or 
moderate injury. It may also be used to alert against unsafe practices or potential 
equipment damage. 

: It indicates additional helpful information. 

 
 

Warnings and cautions

 

Follow the warnings and cautions below when handling this instrument. Information below is to be 
supplemented in each chapter. 

 

 

After  using  this  endoscope,  clean,  disinfect  and  store  it  according  to  the  instruction  manual. 

Before endoscopy, remove any metallic objects from the patient. 

Do  not  strike,  hit,  or  drop  the  endoscope’s  distal  end,  insertion  tube,  bending  section,  control 
section, universal cord, or endoscope connector. Also, do not bend, twist or pull the 

endoscope’s 

distal  end,  insertion  tube,  bending  section,  control  section,  universal  cord,  or  endoscope 
connector  with excessive force. 

Never perform angulation control forcibly or abruptly. 

Never insert or withdraw the endoscope’s insertion tube while the bending section is locked in 
position. 

Never  operate  the  bending  section,  feed  air  or  perform  suction,  insert  or  withdraw  the 
endoscope’s  insertion  tube,  or  use  endotherapy  accessories  without  viewing  the  endoscopic 
image or while the image is frozen or magnified. 

Do  not  touch  the  endoscope  connector  immediately  after  removing  it  from  the  endoscope 
imaging processor because it is extremely hot. 

When  the  endoscopic  image  does  not  appear  on  the  monitor,  the  sensor  may  have  been 
damaged. Turn the imaging processor OFF immediately. 

If it is difficult to insert the endoscope, do not forcibly insert the endoscope; stop the endoscopy. 

Be  sure  to  inspect  that  the  bending  section  bends  smoothly  by  touching  it  with  hands  before 
inserting the endoscope into the patient. Immediately stop using it and withdraw it from the patient 
if any irregularity is observed. 

Keep  the  insertion  section  and  bending  section  as  straight  as  possible  during  endoscopic 
treatment to give smooth access to the endoscopic instrument. 

 

 

CAUTION

 

NOTE

 

Summary of Contents for VET-1335








































Reviews: