background image

3

•   Do not spill water or other liquids on or into the unit.
•   Make sure power outlets are conform to the power requirements listed on the 

back of the unit.

•   Do not use the unit if the electrical power cord is frayed or broken.
•   Do not connect the inputs/outputs of amplifiers or consoles to any other 

voltage source, such as batteries, mains sources or power supplies, regardless 
of whether the amplifier or console is turned on or off. 

•   Power down and disconnect units from mains voltage before making 

connections.

•   Do not use the unit near stoves, heat registers, radiators, or other heat 

producing devices.

•   Do not remove the cover. Removing the cover will expose you to potentially 

dangerous voltages. 

•   Do not drive the inputs with a signal level higher than that required to drive 

equipment to full output. 

•   Do not run the output of any amplifier back into another input.
•   In case of malfunction, this device should be serviced by qualified service 

personnel only. If not serviced by qualified personnel, warranty may be void.

•   For indoor use only! Do not expose the speaker to high humidity levels and/or  

high ambient temperatures.

•   Avoid exposure to direct sunlight. Long term exposure to high UV radiation 

may cause color changes over time.

Summary of Contents for OVO8-BL

















Reviews: