29
5) Water tubing connection is leaking on the system
If you are experiencing a water leak from any of the tubing connections on the reverse osmosis system,
Please review the steps below to address the connection.
Please follow the steps below:
Step 1.
Turn off the cold supply water to the system.
Step 2.
Please verify the end plugs are removed prior to new system installation or filter replacement.
Step 3.
Please push the water tubing into the quick connect fitting more securely. If this doesn’t
resolvethe issue, with the water turned off, please remove the tubing by pressing in on the
collet ring and make a clear cut on the outer tip of tubing, push the tubing into the fitting
securely and this should take care of the leak issue.
If the leak issue continues, please contact APEC technician for assistance.
4) Tank Takes Long Time To Fill
(does not meet claimed GPD)
- Insufficient water pressure (below 50 psi for non-pump systems)
—>
Increase house water pressure or
add an appropriate pump to system.
- Low water temperature (below 77 degree F )
—>
Increase house water pressure or add pump to com-
pensate for low (cold) water temperature.
Claimed GPD:
The claimed gallon per day (GPD) flow rate for each RO model is rated based on
60 psi
input water
pressure at
77 degree F
water temperature. At this standard water pressure and temperature, the RO
-Quick90 gpd system should make about 3.7 gal of filtered water per hour, the 4-gal tank should fill in
1-1.5 hours.
Lower water pressure and colder temperature will slow the system’s output to less than the claimed GPD
flow rate.
Please check your water pressure as the first step in determining the cause of slow flow rate
(low GPD)
.
3) Sluggish Flow At Dispensing Faucet
- Insufficient water pressure (see “
RO Basics
” for explanation)
—>
Check water pressure. If too low for this
chosen RO model, either increase your water pressure or add pump to RO system.
- Input water to RO is blocked
—>
Make sure Feed water valve is fully opened and unhindered.
- Tank not filled yet
—>
Wait until tank is more filled, takes
2-3 hours
average.
- Low tank pre-charge pressure
—>
Raise tank pre-charge to 5-7 psi.
29
5)
5)
W
Water tubing connection is leak
k
in
in
g
g
on
o
the system
g
g
g
y
If you are experiencing a wate
te
r
r le
le
a
ak from any of the tubing connec
ec
ti
ti
on
o
s
o
on the reverse osmosis system,
Please review the steps be
be
low
w
to
to
address the connection.
Please follow the st
t
ep
ep
s
s
be
be
low:
Step 1.
Turn off the cold supply water to the system.
Step 2.
Please verify the end plugs are removed prior to new system installation or filter
r
r
rep
ep
la
la
c
cement.
Step
ep
3.
Please push the water tubing into th
th
e
e
qu
qu
ick connect fitting more securely. If
f
th
this
is
d
oesn’t
resolvethe issue, with the wat
t
er
er
t
tur
ur
n
ned off, please remove the tubing b
b
y
pr
pres
es
sing in on the
collet ring and make a cle
e
ar
ar c
c
ut
ut
on the outer tip of tubing, push the
e t
t
ub
ubin
in
g into the fitting
securely and this should
t
t
ak
ak
e
e care of the leak issue.
If the leak issue cont
t
in
in
ue
ues
s, please contact APEC technician fo
o
r
r
as
as
si
sist
stance.
4) Tank Takes Lo
Long
ng Time To Fill
g
g
(does not meet claim
im
ed
ed
GPD)
- Insufficie
e
nt
nt
w
wat
at
e
er pressure (below 50 psi for non-
n-
pu
pump
mp systems)
—>
Increase house wate
te
r pr
pr
es
es
sure or
add an
an a
a
pp
pp
r
ropriate pump to system.
- L
L
ow
ow
w
w
ater temperature (below 77 degre
e
e
e F )
)
—>
Increase house water pressure o
o
r
r
ad
ad
d
d pump to com-
pe
pe
ns
n
ate for low (cold) water tempera
a
tu
tu
re
re.
Cl
Claimed GPD:
The claimed gallon per
r d
day
ay
(
(
GP
G
D) flow rate for each RO model is rated based on
60 psi
input water
pressure at
77 degree
F
F
w
wat
ate
er temperature. At this standard water pressure and temperature, the RO
-Quick90 gpd system should make about 3.7 gal of filtered water per hour, the 4-gal tank should fi
fi
ll in
1-1.5 hours.
Lower water pressure and colder temperature will sl
sl
ow
ow t
t
h
he system’s output to less than the cl
clai
aime
me
d
GPD
flow rate.
Please check your water pressure as th
h
e
e fi
firs
rst
t step in determining the cause of slo
low
w
fl
flow rate
(low
w
G
G
PD
P
)
.
3) Sluggish
sh
F
F
lo
low
w At Dispensing Faucet
gg
p
g
- Insu
s ff
ff
ic
ic
ie
ient water pressure (see “
RO Basics
” fo
o
r
r e
explanation)
—>
Check water p
p
ressur
ur
e.
e. I
I
f
f too low for this
ch
ch
os
s
en
e
RO model, either increase your wa
ate
te
r
r pr
p
essure or add pump to RO s
s
ys
yste
tem.
m.
- I
Input water to RO is blocked
—>
M
M
ak
ak
e
e
s
sure Feed water valve is fully opened an
and
d unhindered.
- Tank not filled yet
TT
—>
Wait until tank is more filled, takes
2-3 hours
average.
- Low tank pre-charge pressure
—>
Raise tank pre-charge to 5-7 psi.
Summary of Contents for Ultimate RO-QUICK90
Page 2: ......
