4
INSTALLING THE SYSTEM
Space:
Make sure there is sufficient space under the counter for installation (an area of about
14”L x 6”W x 6.5”H
for the system,
11”D x 18”H
for tank).
The RO system is best installed under the kitchen sink. But if that is not feasible you
can install the system anywhere where there is a cold water supply with sufficient
water pressure for the chosen RO model, and an outlet to drain off the drain water
from the system.
Feed Water:
RO systems are designed to treat both hard and soft water and can handle incoming
TDS levels up to 2000ppm.
Note:
Please remove the 2 white plastic zip ties on the RO-QUICK90 system. This is
for shipping protection only.
Step 1: Feed Water Connection
The RO system must be connected to the COLD water supply only!
1. Locate the
Cold
water supply valve under the kitchen sink (the round or oblong handle on
the right side). Turn off the incoming cold water completely by turning the shut off handle
clockwise.
Note:
If the cold water shut off valve can not turn off the water, the main water supply
to the house must be shut off for the installation. Another option is to use a “self
piercing saddle valve” from APEC or from a local hardware store.
2.
Feed Water Adaptor (1/2” or 3/8”):
See
Fig. 1.
The Feed Water Adaptor comes with a
separate Needle Valve. The Adaptor goes inline onto your 1/2” or 3/8” cold water pipe. The
Needle Valve portion screws onto the Adaptor as shown in
Fig. 2.
Fig. 1
A.
1/2” x 3/8” Male-Female Water Supply Adapter
with O-ring.
B.
1/2” x 3/8” Female-Male Converter with O-ring.
C.
1/4” x 1/8” Male Needle Valve.
4
INST
ST
AL
AL
LI
LIN
NG THE SYSTEM
Space:
Make sure there is sufficient s
spa
pace under the counter for installat
t
io
ion
n (a
(a
n
n
area of about
14”L x 6”W x 6.5”H
H
f
f
or
or
t
t
he
he
system,
11”D x 18”H
for tank).
The RO system is best
t i
in
t
stalled under the kitchen sink. But if that is not feasible you
can install the system anywhere where there is a cold water supply with sufficient
water pressure for the chosen RO model, and an outlet to drain off the drain water
from the system.
Feed Water:
RO
RO
systems are designed to treat both ha
ha
rd
rd a
and
nd
soft water and can handle incomin
in
g
g
TD
TD
S
S le
l
vels up to 2000ppm.
No
o
te
te
:
:
Pl
Please remove the 2 white plas
s
ti
tic
c
z
zip ties on the RO-QUICK90 sys
yste
te
m.
m. This is
p
p
y
y
for shipping protection only
y
.
pp g p
y
y
Step 1: Feed Water Connect
ct
io
ion
n
The RO system must
t
b
b
e
e
co
co
nnected to the COLD water supply only!
y
pp y
y
1. Locate the
Cold
water supply valve under the kitchen sink (the round or oblong handle on
the right side). Turn off the incoming cold water completely by turning the shut off handle
clockwise.
Note:
If the cold water shut off valve can
n
no
not
t
tu
tu
r
rn off the water, the main water s
s
up
up
pl
ply
y
to the house must be shut off fo
o
r
r
th
th
e
e in
installation. Another option is to us
us
e
e a
a
“self
piercing saddle valve” from AP
AP
EC
EC
or from a local hardware store.
2.
2.
Fe
ed Water Adaptor (1/2” or 3/
/
8”
8
):
):
See
Fig. 1.
The Feed Water Ada
a
pt
pt
or
or
c
c
omes with a
separate Needle Valve. The Ada
apt
pt
or
or goes inline onto your 1/2” or 3/8
8
”
”
co
cold
ld water pipe. The
Needle Valve portion screws
s on
on
to
to
t
t
h
he Adaptor as shown in
Fig. 2.
Fig. 1
A.
1/2” x 3/8” Male-
F
Female Water Supply Adapter
with O-ring.
B.
1/2” x 3/8” Female-Male Converter with O
O
-r
-r
in
ing
g.
C.
C
1/4” x 1/8” Male Needle Valve.
Summary of Contents for Ultimate RO-QUICK90
Page 2: ......
