background image

June 2013 

80-0180-347 Rev. A 

SYSTEM OVERVIEW 

The A100-3090H electrified trim provides access control to narrow stile alumi-
num  doors  when  combined  with  an  access  control  system  and  Adams  Rite 
locking hardware.   
 
The A100-3090H includes an integrated iCLASS or PROX reader and electri-
fied lever.   The lever handle will not engage the deadlatch or deadbolt until 
authorization  is  received  wirelessly  from  the  access  control  system.    The 
A100-3090H is connected to the access control system through the included 
wireless  Aperio  hub.    The  hub  connects  to  the  access  control  system  with 
Wiegand wiring and signal wiring for REX, DPS, Tamper and Low Battery.   
 
The Aperio™ eForce

®

 will mechanically interface with: Adams Rite MS Series 

Deadbolts; Adams Rite 4500/4900 Deadlatches; Adams Rite 8000 Series Exit 
Devices;  Yale  7200  Series    Narrow  Stile  Exit  Devices;  Corbin  Russwin 
ED4000 Series, and SARGENT 8500 Narrow Design Rim Exit Devices. 

OPERATIONAL SPECIFICATIONS

 

 

IEEE 802.15.4 UHF Interface operating at 2.4GHz 

 

 

iCLASS or PROX Reader technology 

 

AES 128 bit encryption 

 

4-AA battery operated 

 

Operating Temperature Range: -31° to 150°F (-35° to 65°C) 

 

Operating Humidity Range: 5% to 95% relative humidity non-condensing 

 

 

 

June 2013 

17 

80-0180-347 Rev. A 

STEP 8     BATTERY INSTALLATION

 

 

 

Properly  insert  4  (AA)  Alkaline 
batteries  into  battery  holder  ob-
serving the polarity markings.  

 

 

Plug  battery  pack  into  eForce

®

 

connector (F

IG

. 22). 

 

 
 
 
 

 

 
 

 

Insert  battery  case  into  the 
eForce

®

 as shown (F

IG

 23). 

 

 

Slide  battery cover over the bat-
teries. 

 

 

A  battery  moisture  shield  is  pre-
installed at the factory to protect 
the batteries from the elements.  

 
 
 
 
 
 
  
 

 

Insert  5/64”  Allen  key  (included)  
and  turn  clockwise  two  full  turns 
to        secure  the  battery  cover.  
(F

IG

. 24). 

 

 

Aperio  is  activated  when  battery 
cover is installed and secured. 

 

 

The eForce A100-3090H will self
-test and beep once upon instal-
lation of the batteries. 

 

F

IG

. 22 

F

IG

. 23 

F

IG

. 24 

Summary of Contents for eForce A100 A100-3090H











Reviews: