49
JP6
:
(2.0mm Pitch 2x3 Pin Header),COM6 setting jumper, pin 1~6 are used to select signal out of pin
9 of COM6 port.
JP3 Pin#
Function
Close 1-2
RI (Ring Indicator)
(default)
Close 3-4
COM6 Pin9=+5V
(option)
Close 5-6
COM6 Pin9=+12V
(option)
COM6
:
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection to serial
devices. COM6 port is controlled by pins No.1~6 of
JP6
,select output Signal RI or 5V or 12v, For
details, please refer to description of JP6.
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP6 Setting:
Pin1-2 : RI (
Ring Indicator
)
(default)
Pin3-4 : 5V Standby power
(
option
)
Pin5-6:12V Standby power
(option)
S1
:
PWR BT: POWER on/off Button
, They are used to connect power switch button. The two pins
are disconnected under normal condition. You may short them temporarily to realize system
startup & shutdown or awaken the system from sleep state.
PWR LED:
POWER LED status.
S1
Model
TB-528C1U2P1
PS_ON2
Yes
SBC-7106 R110
R12/ NC
Cable
Yes
SBC-7106 R120
R12/ 0ohm
NC
37. TB-528CAN2 R0.10
(
option
)
:
SBC-7106 Riser Card,TB-528CAN2 CN3 connect to SBC-7106 CN3 pin Header. It
provides two CAN-bus Interface.
TB-528CAN2 Top
:
Summary of Contents for ARCHMI-7XX
