background image

 

 

 

 

 

 
 
Aplicom is the registered trademark of Aplicom Oy. 
 

 Aplicom Oy 2016 

 
Printed in Finland. 
 
 
 
 
 
All rights reserved. Reproduction in whole or in part in any form is prohibited without the prior written consent 
of the copyright owner. Aplicom Oy makes every effort to ensure that the information in this manual is correct, 
but accepts no liability for any errors or omission. 
 
Aplicom Oy has a policy of continuous improvement. Therefore we reserve the right to make changes and 
improvements to any of the products described in this guide without prior notice. Due to these improvements, 
the contents of this manual are subject to change without notice. 
 
Aplicom Oy is not responsible for any loss of data, income or any consequential damage. 
 
 

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This  crossed-out  wheelie  bin  means  that  within  the  European  Union  the  product  must  be 
taken to separate collection points at the product`s end-of life. This applies to your device but 
also  to  any  enhancements  marked  with  this  symbol.  Do  not  dispose  of  any  part  of  these 
products as unsorted municipal waste. 

Summary of Contents for A11











Reviews: