Apollo XPander XPA-IN-14011-APO Commissioning Manual Download

Page: 15 / 19

Appendix C

Radio Channels

Ch1: 868.048 MHz

Ch9: 868.248 MHz

Ch17: 868.749 MHz

Ch25: 868.950 MHz

Ch2: 868.073 MHz

Ch10: 868.273 MHz

Ch18: 868.774 MHz

* Ch26: 868.975 MHz

Ch3: 868.098 MHz

Ch11: 868.298 MHz

Ch19: 868.800 MHz

Ch27: 869.000 MHz

Ch4: 868.123 MHz

Ch12: 868.323 MHz

Ch20: 868.825 MHz

Ch28: 869.025 MHz

Ch5: 868.148 MHz

Ch13: 868.349 MHz

Ch21: 868.850 MHz

Ch29: 869.050 Mhz

Ch6: 868.173 MHz

Ch14: 868.374 MHz

Ch22: 868.875 MHz

Ch30: 869.075 MHz

Ch7: 868.198 MHz

Ch15: 868.399 MHz

Ch23: 868.900 MHz

Ch31: 869.100 MHz

* Ch8: 868.223 MHz

Ch16: 868.424 MHz

Ch24: 868.925 MHz

Ch32: 869.125 MHz

* Default channels on power up.

Appendix D

XPander spares

Description

Part Number

Optical detector

XPA-OP-12034-APO

Heat detector A1R

XPA-HT-11170-APO

Heat detector CS

XPA-HT-11171-APO

Mounting base detector

XPA-WB-10022-APO

Red sounder

XPA-SO-14001-APO

White sounder

XPA-SO-14002-APO

Red sounder visual indicator

XPA-SN-14003-APO

Amber sounder visual indicator

XPA-SN-14004-APO

Clear sounder visual indicator

XPA-SN-14005-APO

Red sounder mounting base

XPA-SB-10023-APO

White sounder mounting base

XPA-SB-10024-APO

Combined sounder and detector base

XPA-WB-14036-APO

Combined sounder-visual indicator (red) and detector base

XPA-WB-14037-APO

Combined sounder-visual indicator (white) and detector base

XPA-WB-14038-APO

Appendix E

Site Survey Instructions PP2323 - see next page

Appendix F

Radio Site Survey Sheet - see page 17

Summary of Contents for XPander XPA-IN-14011-APO




















Search results

Summary of Contents for XPander XPA-IN-14011-APO

Reviews:

Related manuals for XPander XPA-IN-14011-APO

Brands by name

Popular brands

Apollo XPander XPA-IN-14011-APO, Commissioning Manual

Search results

Summary of Contents for XPander XPA-IN-14011-APO

Reviews:

Related manuals for XPander XPA-IN-14011-APO

Brands by name

Popular brands