List of Figures-1
PacketMax 5000 Installation and Operation Manual, 10007678 Rev J
List of Figures
Figure 1-1: PacketMax System Elements, 1-3
Figure 1-2: PacketMax System network, 1-5
Figure 1-3: Out of band Management, 1-7
Figure 1-4: Inband Management, 1-8
Figure 1-5: VLAN Application, 1-9
Figure 1-6: PacketMAX 5000 in Point-to-Point Mode, 1-10
Figure 1-7: PacketMax Service Flows, 1-15
Figure 1-8: 3-DES Encryption, 1-18
Figure 2-1: PacketMax Interface for PacketMax 5000, 2-2
Figure 2-2: Slots and port numbers allotment of PM 5000, 2-4
Figure 2-3: Slots and port numbers of four sectors BS, 2-5
Figure 2-4: PacketMax Interface of WSC Card (WSC-24), 2-6
Figure 2-5: PacketMax Interface of WSC-48, 2-8
Figure 2-6: PacketMax Interface of MSC card, 2-11
Figure 2-7: Redundant MSC, 2-14
Figure 2-8: PM 5000 with two AC power supplies installed for redundancy, 2-15
Figure 2-9: Front panel - Power Supply LEDs and the ESD Connector, 2-15
Figure 2-10: Ejector for hot swapping WSC Card, 2-17
Figure 2-11: Front Panel installed in PM 5000 chassis, 2-18
Figure 2-12: Front Panel installed as QWC card, 2-19
Figure 2-13: Fan - PM 5000, 2-19
Figure 2-14: Connecting to the RS-232 Craft Port, 2-20
Figure 2-15: DB 9 (Female) and RJ 11 (Male) pinout, 2-21
Figure 2-16: DC input- Rear of the PM 5000, 2-23
Figure 2-17: AC input- Rear of the PM 5000, 2-24
Figure 2-18: Base Station Radio, 2-25
Figure 3-1: Package Contents, 3-3
Figure 3-2: Mounting Base Station -PM 5000, 3-4
Figure 3-3: Ground lug on the Base Station, 3-5
Figure 3-4: Ground Strap Connector- Front and Rear Panel, 3-5
Figure 3-5: Insterting WSC, MSC and filler panels in to PM 5000 - 4 sector, 3-6
Figure 3-6: Insterting WSC, MSC and filler panels in to PM 5000 - 12 sector, 3-6
Figure 3-7: Connecting IF port cable, 3-7
Figure 3-8: Connecting IF port cable, 3-7
Figure 3-9: Connecting DB 9 serial cable to Management Port, 3-8
Figure 3-10: Connecting Cat 5 cable to the Backhaul port, 3-8
Figure 4-1: PM-BSR-33 and PM-BSR-35 Package Contents- Mounting Hardware, 4-3
Figure 4-2: Grounding lug on 3.3 and 3.5 GHz radio attached to base bracket, 4-5
Figure 4-3: Installation of the Base Station Radio, 4-6
Figure 4-4: Attaching the Base Support Bracket, 4-7
Figure 4-5: Attaching the Inner Mounting Bracket, 4-7
Figure 4-6: Attaching the Grounding Lug, 4-8
Figure 4-7: RF Cable connects BSR to the Antenna, 4-9
List of Figures
Summary of Contents for PacketMAX 5000
Page 10: ...Preface Preface vi PacketMax 5000 Installation and Operation Manual 10007678 Rev J ...
Page 14: ...Table Of Content TOC 4 PacketMax 5000 Installation and Operation Manual 10007678 Rev J ...
Page 146: ...E 4 PacketMax 5000 Installation and Operation Manual 10007678 Rev J Chapter E Certifications ...
Page 150: ...F 4 PacketMax 5000 Installation and Operation Manual 10007678 Rev J Chapter F Troubleshooting ...