background image

SPECIFICATIONS

 

 

CD PLAYER / DAC SECTION 

 

Transport Mechanism 

Philips VAM1201 Short Loader MK3 

Format     

 

Audio CD (CD-DA), CD-Recordable (CD-R), CD-Rewritable (CD-RW) 

Input Data     

 

16 to 24Bits/32 to 96 kHz automatically Locked 

Upsampler     

 

44.1 kHz, 96 kHz, 192 kHz selectable 

DAC    24/192 Delta-Sigma Digital to Analog Converter 

Output word Length     

16, 18, 20, 24 Bits 

Dynamic Range       

110 dB Type 

Signal-to-Noise Ratio     

120 dB Type 

Distortion    

 

0.003 %, 1 kHz 

0.002 %, 10 kHz 

0.002 %, 20 kHz 

Frequency Range     

10 Hz - 20 kHz (-0.5dB) 

Sampling Frequency     

44.1 kHz to 192 kHz, automatic 

Power Consumption   

10 Watts 

Dimension (WHD)       

435 x 72.5 x 344.5 mm 

AC Mains     

 

100/120/220/230 V, 50 or 60 Hz 

Analog Output       

Full balanced Class A operation 

Full functional remote control (RC-5) 

 

Separate Toroidal Transformers for analog and digital circuits. Separate Stages of power regulations for 

each function blocks. High quality electronic components and gold plated RCA connectors. 

 

INPUT/OUTPUT 

 

Analog Output 

  1 RCA / Unbalanced stereo L & R channel 

1 XLR / Balanced stereo L & R channel (100 Ohm) 

Digital Output     

 

1 Coaxial (RCA, 75 Ohm), 1 Toslink (Optical) 

Digital Input     

 

1 Coaxial, 1 Toslink, 1 IEEE1394 (Upgrade Provision) 

 

 

* All specifications are subject to improvement without further notice.

 

 

Stello CDA200 

12

Summary of Contents for Stello CDA200















Reviews: