background image

10 

If the temperature differential is large than 75ºF, there is probably a problem with your system. It may not be the 
thermostat. First make sure you thermostat probe is flat against the griddle plate and is making good contact. 
Dirt  under  the  probe  will  cause  inaccurate  readings.  Next  make  sure  the  thermostat  bulb  is  held  tightly  in  its 
holder. If you can pull the capillary tube and the bulb moves it is not held tight enough against the griddle plate. 
This  will  cause  variations  in  the  temperature  of  the  griddle  surface.  If  both  of  these items  have  been  checked 
and you still have a differential over 75ºF then the thermostat is bad replace it. 

Determine the average temperature 

Note the temperature for each section of the griddle as the burners ignite.  

Note the temperature for each section of the griddle as the flame extinguishes.  

The flame extinguish temperature plus the flame ignition temperature divided by two equals the average 
temperature.  

EXAMPLE:

 

Flame extinguished 367ºF 

 

Flame ignition 341ºF 

 

708º / 2 

 

Average temperature = 354ºF 

If the average temperature is within 15ºF of the dial marking you probably leave the calibration where it is. If the 
average temperature is outside of 15ºF of the dial setting you will want to calibrate the thermostat. To calibrate a 
thermostat first remove the knob by pulling it straight off the shaft. Next take a small flat head screw drive and 
turn  the  screw  inside  the  shaft,  clockwise  to  decrease,  counterclockwise  to  increase.  ¼  turn  clockwise  will 
decrease  the  temperature  approximately  24ºF.  ¼  turn  counterclockwise  will  increase  the  temperature 
approximately  24ºF.  Adjust  and  re-measure  the  average  temperature  until  you  get  the  temperature  to  your 
desired point. 
 
NOTE:  avoid  making  more  than  ½  turn  at  a  time.  Calibration  is  not  linear  and  you  can  get  the  thermostat 
significantly out of calibration to a point where it is difficult to reset.  
 
If  after  adjusting  the  thermostat  three  times  and  getting  no  change  in  calibration  the  thermostat  is  bad.  Then 
replace the thermostat. 
 

NOTES: _________________________________________________________________________________ 

_________________________________________________________________________________________ 

________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 
 
_________________________________________________________________________________________ 
 
_________________________________________________________________________________________ 

Summary of Contents for GGM -24i

















Reviews: