background image

IMMEDIATELY INSPECT FOR SHIPPING DAMAGE 

All  containers  should  be  examined  for  damage  before  and  during  unloading.  The  freight  carrier  has  assumed 
responsibility for its safe transit and delivery. If equipment is received damaged, either apparent or concealed, a 
claim must be made with the delivering carrier. 

A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by 
the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the 
necessary forms. 

B)  Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection must be 
made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all contents and 
packaging material. 

Installation  and  start-up  should  be  performed  by  a  qualified  installer  who  thoroughly  read,  understands  and 
follows these instruction. 

If  you  have  questions  concerning  the  installation,  operation,  maintenance  or  service  of  this  product,  write 
Technical  Service  Department  APW  Wyott  Foodservice  Equipment  Company,  P.O.  Box  1829,  Cheyenne,  
WY 82003.

 

SAFETY PRECAUTIONS 

 

Before installing and operating this equipment be sure everyone involved  in its operation is fully trained and is 
aware  of  all  precautions.  Accidents  &  problems  can  result  by  a  failure  to  follow  fundamental  rules  and 
precautions. 

The following words and symbols, found in this manual, alert you to hazards to the operator, service personnel 
or the equipment. The words are defined as follows: 

 

DANGER:

  This  symbol  warns  of  imminent  hazard  which  will  result  in  serious  injury  or 

death. 

 

 

 

WARNING:

 This symbol refers to a potential hazard or unsafe practice, which could result 

in serious injury or death. 

 

 

 

CAUTION:

 This symbol refers to a potential hazard or unsafe practice, which may result in 

minor or moderate injury or product or property damage. 

 

 

 

NOTICE:

  This  symbol  refers  to  information  that  needs  special  attention  or  must  be  fully 

understood even though not dangerous. 

 

 
 

 

NOTICE:

 This product is intended for commercial use only. Not for household use. 

 

 

 

CAUTION:

  These  models  are  designed,  built,  and  sold  for  commercial  use.  If  these 

models  are  positioned  so  the  general  public  can  use  the  equipment  make  sure  that 
cautions,  warnings,  and  operating  instructions  are  clearly  posted  near  each  unit  so  that 
anyone  using  the  equipment  will  use  it  correctly  and  not  injure  themselves  or  harm  the 
equipment. 

 

 

 

WARNING:

  Improper  installation,  operation,  service  or  maintenance  can  cause  property 

damage,  injury  or  death.  Read  and  understand  these  instructions  thoroughly  before 
positioning, installing, maintaining or servicing this equipment. 

 

 

Summary of Contents for GGM -24i

















Reviews: