Installation and user manual aquagraFX for GTX 680 Lightning, 08/2012
Description
Description
Description
Description
Thank you for purchasing a graphics card
waterblock manufactured by Aqua Computer. The
aquagraFX for GTX 680 Lightning has been
specifically designed for graphics cards according
to reference design of the chip manufacturer. The
aquagraFX for GTX 680 Lightning effectively cools
the RAM, voltage regulators and GPU of your
graphics card. The base part of the waterblock is
manufactured from pure copper for outstanding
performance and durability.
Installation
Installation
Installation
Installation
Step 1:
Remove the originally installed air cooling unit
from the graphics card. The procedure necessary
to perform this might slightly vary depending on
the graphics card. Use extreme caution not to
damage any of the highly sensitive components of
the graphics card! Disconnect the fan connector
while lifting the air cooling unit off the graphics
card.
Step 2:
Remove all thermally conductive pads from the
graphics card and clean all surfaces with direct
contact to the cooling unit from remaining thermal
compounds using benzine if necessary.
Apply a thin layer of thermal compound to the
GPU and the RAM modules. These components
are marked red in the figure. The thermal
compound must not be electrically conductive! Cut
fitting pieces from the thermally conductive pad
supplied with the aquagraFX and place them on
top of the voltage regulators as indicated by green
rectangles.
Step 3:
Attach the aquagraFX for GTX 680 Lightning to the
graphics card. The original back plate will be
reused. At first carefully and evenly screw in the
four screws adjacent to the GPU (four screws M3 x
4 mm), afterwards the remaining screws (five
screws M3x6 mm). Secure the lateral areas of the
back plate with four screws M3 x 6 mm and fittings
hex nuts M3 supplied with the aquagraFX.
Step 4:
Carefully check that the waterblock has level
contact to all relevant components of the graphics
card. Do not power on the graphics card or the
PC if the cooler does not perfectly fit the graphics
card! In this case, disassemble and repeat the
mounting procedure. All screws must not be overly
tightened to prevent the PCB from twisting!
Step 5:
Insert the graphics card to your PC and integrate
the waterblock into your cooling system. Be sure
not to connect any waterblocks in parallel but only
consecutively. A detailed instruction on building a
watercooling system and plug&cool connectors as
well can be found on our website
www.aqua-computer.de
– please check the section
support/download.
Step 6:
Put the water cooling system into operation, but do
not connect any other PC components to the
mains supply! Check the waterblock as well as the
fittings for leakages and do not put your PC into
operation unless you can definitively eliminate the
possibility of coolant leaking from the system! If
any component has been in contact with coolant,
do not put it into operation before it is completely
dry again! For operating the graphics card, the
waterblock must be correctly mounted and be
connected to a water cooling system featuring
adequate cooling performance! For corrosion
inhibition, either Double Protect Ultra or a mixture
of water and ACfluid according to the preparation
instructions provided with ACfluid must be used as
coolant!
ATTENTION:
ATTENTION:
ATTENTION:
ATTENTION:
Disregarding the instructions may lead to severe
Disregarding the instructions may lead to severe
Disregarding the instructions may lead to severe
Disregarding the instructions may lead to severe
damages! Aqua Computer GmbH & Co. KG
damages! Aqua Computer GmbH & Co. KG
damages! Aqua Computer GmbH & Co. KG
damages! Aqua Computer GmbH & Co. KG
cannot be held liable for damages or injuries
cannot be held liable for damages or injuries
cannot be held liable for damages or injuries
cannot be held liable for damages or injuries
resulting from improper installation or use of the
resulting from improper installation or use of the
resulting from improper installation or use of the
resulting from improper installation or use of the
product!
product!
product!
product!
Thank you again for choosing an aqua computer
product.
© 2012
Aqua Computer GmbH & Co. KG – Gelliehäuser Str. 1 – D-37130 Gleichen
computer
aqua
