background image

TEMPERATURE CONTROL 

18 

BATHROOM CONTROLLERS 

The Bathroom controller(s) allows the user to select the temperature setting for the hot water to be used in 
the bathroom. They have a minimum temperature setting of 37°C and a maximum temperature setting of: 

 

CF20-60 series 

50°C 

 

CF20-50 series 

48°C 

The Bathroom controllers operate in tandem. Whenever an operation is selected on one Bathroom controller, 
it is also set on the other Bathroom controller. The Bathroom controllers automatically have priority if they are 
on. 
 

Important:

  It  is  important  to  turn  on  the  Bathroom  controller  before  opening  a  hot  tap  in  the  bathroom 

(priority  is  automatically  gained).  If  the  Bathroom  controller  is  not  on  and  the  Kitchen  controller  is  on  (has 
priority),  then  it  is  possible  to  receive  water  at  a  temperature  higher  than  expected  from  a  hot  tap  in  the 
bathroom. This temperature could be up to: 

 

CF20-60 series 

50°C  if  a  temperature  limiting  device  is  installed  in  the  hot  pipe  to  the 
bathroom or up to 60°C if a temperature limiting device is not installed. 

 

CF20-50 series 

48°C 

 

Notes on the Bathroom controllers: 

 

The controller cannot be turned on whilst a hot tap is open. 

 

When a Bathroom controller is turned on, it gains priority from the Kitchen controller. 

 

The  Bathroom  controller  must  be  on  in  order  to  adjust  the  temperature  setting  on  the  Bathroom 
controller. 

 

The Kitchen controller can be turned off from a Bathroom controller. 

 

Press and hold the on / off button on a Bathroom controller for three seconds. 

This turns off all the controllers and the displays go blank. 

If hot water is flowing from a hot tap, it will go cold. 

 

 Warning:

 It is advised to  leave the Bathroom controller on after hot  water usage is finished  in the 

bathroom. 

Turning  off  a  controller  in  one  bathroom  will  also  turn  off  the  controller  in  the  other 

bathroom

. The Kitchen controller will gain priority if it is on and the temperature setting can be up to: 

 

CF20-60 series 

60°C 

 

CF20-50 series 

48°C 

If a hot tap is open in another bathroom, the water will be delivered at this temperature. 

 

 

 

Bathroom Controller 

Summary of Contents for CF20 series

























































Reviews: