background image

17

Example:

An 11,000 gallon pool with a salt level of 500-ppm

• The column value for 1000 gallons is 21 pounds

• The column value for 10,000 gallons is 209 pounds.

• The total of 230 pounds of salt is needed to reach pool salt level of 3000-ppm.

Salt Addition Chart:

To use this chart:

1

Find current salt level (ppm or g/l) in the left column.

2. Find pool/spa volume in the second row (Gallons or Liters).

3. Find the amount of salt needed to bring pool to the ideal level by finding the intersection of the

row and column.

REFERENCE SECTION

The salt is constantly recycled during normal operation. Loss of salt during a swimming season should
be minimal. Filter backwashing, draining due to rain water overflow, splashing and bathing suit drag out,
and leaks (excessive salt loss in a short span of time) are typical ways salt is lost. Salt does not leave
the pool when water evaporates.

1,000

2,500

5,000

7,500

10,000

12,500

15,000

17,500

20,000

(3,786)

(9,465)

(18,930)

(28,395)

(37,860)

(47,325)

(56,790)

(66,255)

(75,720)

0

25

63

125

188

250

313

376

438

501

(11)

(28)

(57)

(85)

(114)

(142)

(170)

(199)

(227)

250

23

57

115

172

230

287

344

402

459

(0.25)

(10)

(26)

(52)

(78)

(104)

(130)

(156)

(182)

(208)

500

21

52

104

157

209

261

313

365

417

(0.50)

(9)

(24)

(47)

(71)

(95)

(118)

(142)

(166)

(189)

750

19

47

94

141

188

235

282

329

376

(0.75)

(9)

(21)

(43)

(64)

(85)

(106)

(128)

(149)

(170)

1,000

17

42

83

125

167

209

250

292

334

(1.0)

(8)

(19)

(38)

(57)

(76)

(95)

(114)

(133)

(151)

1,250

15

37

73

110

146

183

219

256

292

(1.25)

(7)

(17)

(33)

(50)

(66)

(83)

(99)

(116)

(133)

1,500

13

31

63

94

125

157

188

219

250

(1.5)

(6)

(14)

(28)

(43)

(57)

(71)

(85)

(99)

(114)

1,750

10

26

52

78

104

130

157

183

209

(1.75)

(5)

(12)

(24)

(35)

(47)

(59)

(71)

(83)

(95)

2,000

8

21

42

63

83

104

125

146

167

(2.0)

(4)

(9)

(19)

(28)

(38)

(47)

(57)

(66)

(76)

2,250

6

16

31

47

63

78

94

110

125

(2.25)

(3)

(7)

(14)

(21)

(28)

(35)

(43)

(50)

(57)

2,500

4

10

21

31

42

52

63

73

83

(2.5)

(2)

(5)

(9)

(14)

(19)

(24)

(28)

(33)

(38)

3,000

(3.0)

3,500

(3.5)

35,000

OK for Pool Pilot Operation - (salt water would need to be diluted to lower salt level)

Pounds(kilograms) of Salt needed to attain 3000 ppm (mg/l)

Pool/Spa Volume in Gallons (Liters)

Current 

level of 

salt ppm 

(mg/l)

Ideal

OK

For volumes other than what is shown, use combinations of various columns.

Standard Pool Salt

Summary of Contents for 75090

































Reviews: