background image

CYLINDER/PISTON/CRANKSHAFT PARTS LIST

Key # 

Description 

Stock #

  1 

Spark Plug NGK CMR6A 

FJIG7475

 2 

Cylinder 

Set 

FJIG4382

  3 

Hex Bolt 5x18mm/S (4) 

FJIG8290

 4 

Cylinder 

Gasket 

FJIG4291

  5 

Piston Ring (2) 

FJIG6651

 6 

Piston 

Set 

FJIG6362

 7 

Piston 

Pin 

FJIG3446

  8 

Piston Pin Retainer (2) 

FJIG6509

  9 

Water Jacket Complete 

FJIG8721

 10 

Screw 

3x8mm 

FJIG7160

 11 

Crankshaft 

Complete 

FJIG4091

  12 

Needle Bearing F-910 1.4x8.5mm 

FJIG6149

  13 

Woodruff Key 3x13x4.5mm 

FJIG7660

 14 

O-ring 

G45 

FJIG6251

  15 

Spark Plug Cap Assembly 

FJIG7500

 16 

O-ring 

G30 

FJIG6252

  20 

Ignition Coil Complete 

FJIG7313

  28 

Hex Bolt 4x18mm/WS (2) 

FJIG8220

19

REPLACEMENT PARTS

To order replacement parts for the Fuji-Imvac BT-28M, use the order numbers in the 

Replacement Parts Lists

 that follow. 

Replacement parts are available only as listed. Replacement parts are not available from Product Support, but can be 
purchased from hobby shops or mail order/Internet order fi rms. If you need assistance locating a dealer to purchase 
parts, visit 

www.greatplanes.com

 and click on 

“Where to Buy.”

CRANKCASE PARTS LIST

Key # 

Description 

Stock #

  14 

Crankcase Assembly BT-28 

FJIG3881

  15 

Oil Seal TB 12227 (2) 

FJIG6300

  16 

Ball Bearing 6001 CE (2) 

FJIG3080

  17 

Crankcase Gasket  

FJIG3921

 18 

Shim 

0.2 

FJIG7350

 18 

Shim 

0.3 

FJIG7380

  24 

Magneto Rotor 60mm 

FJIG5720

 25 

Washer 

8mm 

FJIG8680

  26 

Hex Nut 8mm 

FJIG8520

  32 

Hex Bolt 5x18mm/S (3) 

FJIG8290

  55 

Starter Pulley Assembly 

FJIG7139

 56 

Starter 

Pawl 

FJIG7141

  57 

Starter Pawl Spring 

FJIG7142

FUJI-IMVAC BT-28 MARINE ENGINE EXPLODED VIEWS

Summary of Contents for Rio 51

























Reviews: