background image

6

P

LACEMENT

 

(

CONT

.)

>

>

>

50'

>

>

50'

>

25'

>

>

25'

Large Structures, Natural Ventilation

In large structures with natural ventilation, propel fog 

the length of the structure with the first fan row no more 

than 25' from the end wall. The first fan should be:

    - centered along the end wall (or)

    - placed no more than 25' from the side wall, 

      with additional fans in the row equally spaced no 

      farther than 50' apart.

Lengthwise, the fans should be equally spaced and no 

more than 50' apart. All fans should be equipped with 

oscillation, sweeping 360˚.

Large Structures,

Closed or Minimum Ventilation

In closed structures with little to no ventilation, propel 

fog the length of the structure with the first fan row no 

more than 40' from the end wall. The first fan should 

either be:

    - centered along the end wall (or)

    - placed no more than 40' from the side wall, 

      with additional fans in the row equally spaced     

      no farther than 80' apart.

Lengthwise, the fans should be equally spaced and no 

farther than 80' apart. All fans should be equipped with 

oscillation, sweeping 360˚.

>

>

>

80'

>

>

80'

>

40'

>

>

40'

www.JigglyGreenhouse.com  |  (800) 878-7829  |  Sales@JigglyGreenhouse.com

Summary of Contents for GT 500-HS



















Reviews: