background image

North Sports, Inc.    #1 North Shore Dr, SE    White Salmon, WA  98672      TEL: (509) 493-4938      FAX: (509) 493-4966

www.Aquaglide.com

25-26

Supersport

 Owner’s Manual

NOTICE! - Release of Liability, Claim Waiver, and Assumption of Risk Agreement

By opening and assembling this product, you are agreeing (1) to be bound to the terms set forth below and (2) to require anyone using this product to be bound by such terms.  If you are 

unwilling to be bound by these terms, return this product (before use) for a full refund.

ASSUMPTION OF RISK: 

 

Use of this product and any of its components involves certain inherent risks, dangers, and hazards which can result in serious personal injury and death.  In using the 

product, you freely agree to assume and accept any and all known and unknown risks of injury while using this equipment.  The risks inherent in the sport can be greatly reduced by abiding by 

the Warning Guidelines listed in this Owner’s Manual and by using common sense.  

RELEASE AND WAIVER OF CLAIMS AGREEMENT: 

 

In consideration of the sale of the product to you, you hereby agree to the fullest extent permitted by law as follows:

TO WAIVE ANY AND ALL CLAIMS

 

that you have or may in the future have against  North Sports Inc., and Aquaglide, its distributors and dealers, resulting from use of this product and any of its 

components.

TO RELEASE  

North Sports, Inc. and Aquaglide from any and all liability for any loss, damage, injury, or expense that you or any users of this product may suffer, or that your next of kin may 

suffer, as a result of the use of this product, due to any cause whatsoever, including negligence or breach of contract on the part of North Sports Inc. and Aquaglide in the design or manufacture 

of this product and any of its components.

ARBITRATION: 

 

In further consideration of the sale to you of this product and any of its components, you hereby agree to submit to binding arbitration any and all claims which you believe 

you may have against North Sports Inc. and Aquaglide arising from the use of any North Sports Inc. and Aquaglide equipment or products.  The arbitration shall be pursuant to the rules of the 

American Arbitration Association. Arbitration shall be commenced within (1) year from the date on which any alleged claim first arose.  Further, the arbitration shall be held in White Salmon, 

Washington unless otherwise mutually agreed to by all parties.  The submission to the American Arbitration Association shall be unlimited and the arbitration award may be enforced by any 

Court of competent jurisdiction.

BINDING EFFECT OF AGREEMENT:  

In the event of your death or incapacity, this Agreement shall be effective and binding upon your heirs, next of kin, executors, administrators, assigns, and 

representatives.

ENTIRE AGREEMENT: 

 

In entering into this Agreement, you are not relying upon any oral or written representations other than what is set forth in this agreement and the North Sports Inc. 

and Aquaglide Owner’s Manual.

advance. The RA number must be on the outside of the 

package or it will not be accepted at our warehouse.  

Freight on the returned product must be prepaid or 

it will not be accepted. Upon receipt, Aquaglide will 

make a determination within (30) days. If the product 

is covered under warranty it will be returned to the 

customer at the expense of Aquaglide after repairs can 

be made. If not, the customer will receive a quote for 

repair and/ or replacement as well as any necessary 

cleaning and shipping charges. The customer will have 

30 days to accept the quotation. At the end of 30 days, 

or upon refusal of the quote, Aquaglide will return the 

product in the condition in which it was received at the 

customer’s expense. The customer agrees to authorize 

Aquaglide to charge the customer’s credit card for any 

costs not covered under the terms and conditions of the 

Aquaglide Warranty.

Serial Number

All Aquaglide products are marked with a serial 

number. The serial number may be stamped into the 

PVC directly around the valve, or it may be visible on 

a welded plate near the valve. Please include this 

number when you contact Aquaglide, or your dealer, 

with any warranty claim.

North Sports, Inc. warrants products to be free of 

defects in material or workmanship to the original 

purchaser for a period of One (1) year from date of 

purchase.  This warranty is subject to the following 

limitations:  

1.

 Warranty is valid only with dated proof of purchase in 

the form of the original invoice.   

2.

 Warranty is valid only when the product is used for 

normal recreational activities, and does not cover use in 

schools or rental operations. 

3.

 Aquaglide will make the final warranty determina-

tion which may require inspection and/or photos of the 

product which clearly show defect(s).  We require the 

above be sent to another location of our choice, freight 

prepaid, or by email to 

support@aquaglide.com

.   

4.

 If a product is deemed to be defective by Aquaglide, 

the warranty covers the repair or replacement of the de-

fective product only.  Aquaglide will not be responsible 

for any costs, losses, or damages incurred as a result of 

loss of use of product. 

5.

 This warranty does not cover damage caused by 

misuse, abuse, neglect, or normal wear and tear, includ-

ing, but not limited to, punctures, dragging the product 

over the ground, damage due to excessive sun exposure 

or seam failure due to overinflation in the sun, damage 

caused by improper handling and storage, damage 

caused by use in waves or shore break, and damage 

caused by anything other than defects in materials and 

workmanship.

6.

 This warranty is voided if any unauthorized repair, 

change, or modification has been made to any part of 

the equipment.  Authorization for such must come in 

writing from Aquaglide.

7.

 The warranty for any repaired or replacement equip-

ment is good from the date of the original purchase 

only.

8.

 Any warranty claims must be accompanied by the 

original purchase receipt. The name of the retailer and 

date of purchase must be clear and legible.

9.

 There are no warranties which extend beyond the 

warranty specified here.

Returns and Service Policy

Product can be returned only if a return authorization 

number (RA) is given by Aquaglide in

Warranty

Summary of Contents for Supersport






























Reviews: