background image

Before returning to your retailer, call our customer service department at  
1-888-314-2588, 8 a.m.-6 p.m., EST, Monday-Friday.   
 

 

 

Submersible Waterfall Pump with UV 

1300 Gallons Per Hour 

 

ITEM # WP1300UV

 

 

 

PACKAGE CONTENTS 

 

 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 

  WARNINGS AND CAUTIONS 

WARNING 

 

Risk  of  electrical  shock.  This  pump  is  supplied  with  a  grounding  conductor  and  grounding

–type 

attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly 
grounded, grounding-type receptacle. 

 

Do not exceed the voltage shown on the pump. 

 

Always  disconnect  pump  from  the  power  source  before  beginning  any  maintenance  or  work  on  the 
pump. 

 

Inspect cord for damage before installation and/or maintenance. Replace the entire pump assembly if 
damage is found. 

 

Do not remove the grounding pin from the power cord plug. 

 

Risk  of  electrical  shock:  This  pump  has  not  been  investigated  for  use  in  swimming  pools  or  marine 
areas.  

CAUTION 

 

This pump has been evaluated for use with fresh water only. 

 

Use a proper power source as indicated on the pump label.   

 

Keep the cord away from high temperatures or other heat sources. 

 

Do not pump heated liquids. 

 

Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling. 

 

Operate in fresh water only. Avoid heavily chlorinated water and water with high pH levels. 

 

Do not lift the pump by its power cord. 

 
 

Part 

Description 

Quantity 

Pump 

1-in. adapter with flow control 

Pump barrier bag 

REMINDER 

CALL 1-888-314-2588 

BEFORE RETURNING TO STORE. 

Questions, problems, missing parts? 

Before returning 

to your retailer, call our customer service department at  
1-888-314-2588, 8 a.m.-6 p.m., EST, Monday-Friday

 

 

 

Summary of Contents for WP1300UV









Reviews: