background image

2

solely as a result of the failure of individual LED components to emit light if the number of inoperable components is less than 
10% of the total number of LED components in the Product.

If any Product covered by this warranty is returned by Purchaser within the Warranty Period referred to below in accordance 
with Seller’s Product Return Policy (noted in Schedule “A”), and Seller determines to its satisfaction that such Product failed to 
satisfy this warranty, Seller will, at its option, repair or replace the Product or the defective part, or reimburse Purchaser for the 
purchase price, subject to the limited warranty terms and conditions set forth in attached Schedule “A”. For the purpose of 
clarity, “repair or replacement of the Product or the defective part thereof” does not include any removal or reinstallation costs 
or expense, including without limitation labor costs or expenses. If Seller chooses to replace the Product and is not able to do 
so because it has been discontinued or is not available, Seller may replace it with a comparable product.

This warranty shall become effective only upon satisfaction of the conditions set forth on Schedule “A”. The warranty shall be in 
effect for a period (the “Warranty Period”) of 5 years from the Product ship date.

This warranty only applies when the product has been properly handled, stored, transported, wired, installed, and operated 
within the electrical values, operating range and environmental conditions provided in the Specifications. Seller will not be 
responsible under this warranty for any failure of the Product that results from external causes such as: acts of nature; physical 
damage; exposure to adverse or hazardous chemical or other substances; use of reactive cleaning agents and/or harsh 
chemicals to clean the Product; environmental conditions; vandalism; fire; power failure, improper power supply, power surges 
or dips and/or excessive switching; induced vibration; animal or insect activity; fault or negligence of purchaser, any end user of 
the Product and/or any third party not an authorized representative of Seller; improper or unauthorized use, installation, 
handling, storage, alteration, maintenance or service, including failure to abide by any product classifications or certifications, 
or failure to comply with any applicable standards, codes, recommendations, product specification sheets or instructions of 
Seller; use of the Product with products, processes or materials supplied by any end user or third party; or any other 
occurrences beyond Seller’s reasonable control.

This warranty shall become void in the event (a) any repairs, modifications, or alterations not specifically authorized by Seller are 
made to the Product by any person, (b) the Product has been serviced by personnel not authorized by Seller, (c) the Product is 
not used for the purpose for which it is designed, (d) the Product is exposed to operating conditions or environments other 
than those mentioned in the Specifications, product brochures, or user manuals, or (e) the serial numbers on the Products 
have been altered, defaced or rendered illegible.

The provisions of this warranty are exclusive and are given and accepted in lieu or any and all other warranties, whether 
expressed or implied, including without limitation any warranty against infringement and any implied warranties of 
merchantability or fitness for particular purpose, all of which are expressly disclaimed. No person, agent, distributor, dealer or 
company is authorized to change, modify or extend the terms of this warranty in any matter whatsoever. Under no 
circumstances shall Seller’s aggregate liability arising out of or in connection with a defective Product, in contract, tort or 
otherwise, exceed the purchase price of the Product to which such liability relates. In no event shall Seller be liable for special, 
incidental, consequential, indirect or compensatory damages, including, without limitation, damages resulting from loss of use, 
profits, business or goodwill.

Seller reserves the right to modify this warranty from time to time and any modifications shall be effective for all orders placed 
on or after the effective date of such revised warranty. 

This warranty may not be transferred or assigned by the original end user and product must be purchased directly from Seller 
or an authorized distributor or representative of Seller.

Summary of Contents for RHEOS












Reviews: