background image

1

Registered Design. Specifications subject to change without notice.

AQUEA

®

 is a registered trademark of Vantage Products Pty. Ltd.

The contents of this manual are the exclusive copyright of AQUEA

®

 and may not be reproduced without written 

permission. 

©

 2022

Whilst every care was taken in preparation of this document, AQUEA

®

 accepts no responsibility for the accuracy of 

the information supplied.

Ref: 475-818-03

1. SEE “GENERAL USAGE” SECTION FOR INSTRUCTIONS 
REGARDING CORRECT OPERATION OF LID  (SEE PAGE 9)

2. DO NOT CARRY LID WITH LID KEY AS THIS MAY RESULT IN 
INJURY OR DAMAGE

3. DO NOT USE HARSH CHEMICALS, ACIDS OR ABRASIVE 
MATERIALS TO CLEAN LID, OUTER FRAME OR LID KEY

4. KEEP LID KEY OUT OF REACH OF CHILDREN. LID SHOULD 
ONLY BE OPERATED BY A CAPABLE ADULT

5. ENSURE FINGERS & TOES ARE CLEAR OF LID WHEN 
LOWERING TO AVOID INJURY

6. DO NOT OPEN SKIMMER WHILE PUMP IS OPERATING

7. DO NOT LEAVE LID KEY IN LID WHEN NOT IN USE. STORE LID 
KEY IN A SAFE PLACE

8. FOR SMOOTH AND RELIABLE OPERATION, KEEP YOUR 
V-LOCK LID FREE OF DIRT, SAND, LEAF MATTER AND DEBRIS 

IMPORTANT - PLEASE NOTE:

SAFETY FIRST

PLEASE ENSURE SUITABLE PERSONAL 

PROTECTION EQUIPMENT AND SAFE 

WORK PRACTICES ARE USED.

Summary of Contents for 475-201













Reviews: