background image

WARNING & SAFETY INSTRUCTIONS 

 

Page 3 

 

Before  you  begin  the  installation  of  the  water  softener,  we  advise 
you  read  and  carefully  follow  the  instructions  contained  in  this 
manual. It contains important  information about  safety,  installation, 
use  and  maintenance  of  the  product.  The  actual  system  that  you 
have  received,  may  differ  from  the  pictures/illustrations  in  this 
Owner's Manual. 

 

 

Failure  to  follow  the  instructions  could  cause  personal  injury  or 
damage  to  the  appliance  or  property.  Only  when  installed, 
commissioned  and  serviced  correctly,  the  water  softener  will  offer 
you many years of trouble-free operation. 

 

 

The water softener is intended to 'soften' the water, meaning  it will 
remove  hardness  minerals;  it  will  not  necessarily  remove  other 
contaminants present in the water. The water softener will not purify 
polluted water or make it safe to drink! 

 

 

Installation  of  the  water  softener  should  only  be  undertaken  by  a 
competent  person,  aware  of  the  local  codes  in  force.  All  plumbing 
and  electrical  connections  must  be  done  in  accordance  with  local 
codes. 

 

 

Before  setting  up  the  water  softener,  make  sure  to  check  it  for  any 
externally visible damage; do not install or use when damaged.  

 

 

To  prevent  accident  or  injury,  do  not  hoist  the  water  softener  over 
your shoulder. Do not lay the water softener on its side.  

 

 

Keep this Owner's Manual in a safe place and ensure that new users 
are familiar with the content.  

 

 

The water softener is designed and manufactured in accordance with 
current  safety  requirements  and  regulations.  Incorrect  repairs  can 
result in unforeseen danger for the user, for which the manufacturer 
cannot  be  held  responsible.  Therefore  repairs  should  only  be 
undertaken  by  a  competent  technician,  familiar  and  trained  for  this 
product. 

 

 

In  respect  of  the  environment,  this  water  softener  should  be 
disposed  of  in  accordance  with  Waste  Electrical  and  Electronic 
Equipment requirements.  Refer to national/local  laws and codes for 
correct recycling of this water softener. 

Summary of Contents for Micro Budget

















Reviews: