PY500AC SLIDING GATE OPERATOR
12
Cancel width of pedestrian mode, keep auto-close function of pedestrian mode: Turn on the second
and the third DIP-switch (See Fig.9) to ON position. Press button 4 to open the gate (see
Verify
Verify
Verify
Verify open
open
open
open
direction
direction
direction
direction
section). Wait for more than 15 sec.. Then press the same button/button 4 to stop the gate.
Wait some seconds according to your requirements (1~44 sec.). Then press the same button/button
4 to close the gate, press the same button again to stop the gate or the gate will stop automatically at
its closed position if the limit switch is reached. After this setup is complete, return DIP-switch 3 to
OFF position immediately. Thus the width of pedestrian mode has been canceled, the auto-close
function of pedestrian mode has been reserved.
Note: the new auto-close time of pedestrian mode has been re-programmed in the device and
replaced the original auto-close time of pedestrian mode that you have been set in
Set
Set
Set
Set auto-close
auto-close
auto-close
auto-close
function
function
function
function of
of
of
of pedestrian
pedestrian
pedestrian
pedestrian mode
mode
mode
mode
section.
Keep width of pedestrian mode, cancel auto-close function of pedestrian mode
::::
Turn on the second
and the third DIP-switch (See Fig.9) to ON position. Press button 4 to open the gate (see
Verify
Verify
Verify
Verify open
open
open
open
direction
direction
direction
direction
section). Wait some seconds (3~10 sec.), then press the same button/button 4 to stop the
gate. Wait until the gate close automatically (45 sec.). Press the same button again to stop the gate
or the gate will stop automatically at its closed position if the limit switch is reached. After this setup is
complete, return DIP-switch 3 to OFF position immediately. Thus the width of pedestrian mode has
been reserved, the auto-close function of pedestrian mode has been canceled.
Note: the new width of pedestrian mode has been re-programmed in the device and replaced the
original width.
If you open the gate with button 4, the gate will stop at the expected position that you have set, but
the gate will not close automatically.
�
�
�
�
Turn on the second DIP-switch to OFF position (Factory preset: OFF position), both auto close
function and auto-close function of pedestrian mode were shut off.
Note:
Note:
Note:
Note:
(1)
(1)
(1)
(1) You
You
You
You must
must
must
must follow
follow
follow
follow the
the
the
the operating
operating
operating
operating instruction
instruction
instruction
instruction as
as
as
as above,
above,
above,
above, any
any
any
any wrong
wrong
wrong
wrong operation
operation
operation
operation is
is
is
is not
not
not
not allowed
allowed
allowed
allowed during
during
during
during
setting.
setting.
setting.
setting. If
If
If
If your
your
your
your device
device
device
device responds
responds
responds
responds to
to
to
to your
your
your
your requested
requested
requested
requested function
function
function
function correctly,
correctly,
correctly,
correctly, you
you
you
you have
have
have
have set
set
set
set the
the
the
the
function
function
function
function successfully
successfully
successfully
successfully,,,, otherwise
otherwise
otherwise
otherwise repeat
repeat
repeat
repeat the
the
the
the above
above
above
above setup
setup
setup
setup instruction
instruction
instruction
instruction until
until
until
until your
your
your
your device
device
device
device
responds
responds
responds
responds to
to
to
to your
your
your
your expected
expected
expected
expected function.
function.
function.
function.
(2)
If
If
If
If the
the
the
the gate
gate
gate
gate can
can
can
can not
not
not
not be
be
be
be moved,
moved,
moved,
moved, please
please
please
please check
check
check
check whether
whether
whether
whether the
the
the
the gate
gate
gate
gate is
is
is
is obstructed
obstructed
obstructed
obstructed or
or
or
or the
the
the
the gate
gate
gate
gate is
is
is
is too
too
too
too
