info@matermacc.it
Use and maintenance handbook
Page 27
6. MAINTENANCE
In case of damage, the operator
must stop the machine, take off
the ignition key, jump off the trac-
tor and determine the entity of
the damage and then proceed to
intervene on the machine.
Please note that all maintenance operations must be carried
out by qualified and trained workers, when the machine is
off.
It is also very important that all maintenance or repair inter-
ventions are not carried outside but in a specific equipped
garage.
During the operations of use,
regulation, maintenance, repair
or movement, the operator must
make use of the adequate Person-
al Protective Equipment.
Before starting all maintenance operation, the following in-
structions must be followed:
During the maintenance the machine must be placed on an
even surface;
•
During the maintenance the machine must be placed on
an even surface;
•
Turn off the engine of the tractor, pull the drum brake
and take out the ignition key from the panel;
•
Always make correct use of the Personal Protection
Equipment (protective shoes, overall and gloves, mask);
•
Use all the accident prevention means relative to the
operation under way.
•
Where using compressed air to clean the machine, you
must use protective eye wear;
•
When the maintenance of the machine requires to ac-
cess parts that cannot be reached from standing on
the ground, or points higher than 1,50 m, use a stairs or
platforms in compliance with the in rule regulations;
•
Do not carry out unfamiliar reparations. Always follow in-
structions and where they are missing, contact the ma-
nufacturer or expert personnel.
•
Warning: replace the hydraulic pipes when these are da-
maged.
•
Make sure that the lifting mean chosen is suitable for the
operations to be carried out and is in compliance with
the safety regulations;
•
Do not keep the engine of the machine on in closed
areas with no ventilation system able to eliminate the
exhausting gases concentrating in the air;
•
Avoid long and repeated skin contacts with fuels/lubri-
cants/fluids, since these could generate inflammations
or other skin pathologies;
•
Do not ingest fuels/lubricants/fluids. In case of acciden-
tal contact with the eyes, carefully wash the area with
water;
•
Do not weld in closed areas or with an inappropriate
ventilation;
•
Do not weld on or besides painted surfaces to avoid the
propagation of toxic fumes. Remove the paint with spe-
cific products, then wash the surface and let dry;
•
When using compressed air, always wear goggles with
side-protections, and mask in order to avoid the danger
of personal lesions due to dust particles. It is preferred to
clean the machine in ventilated areas.
6.1. MAINTENANCE
INTERVENTIONS
THATMAY BE CARRIED OUT BY THE
OPERATOR
The interventions described in the following paragraphs
do not require a technical specialization. The operator must
know and accurately perform the indications and must have
turned off the machine.
Periodical check-ups and maintenance operations must be
carried out in the periods and modalities described and are
at charge of the operator.
Not observing the periods and modalities of maintenance
will endanger the correct functioning of the machine, thus
breaking the warranty validity.
Intensify the frequency of maintenance interventions in case
of hard use (frequent arrests and start-ups, very hard soils,
etc..).
•
Regularly check that the signs and safety disposals on
the machine are in good state and that nothing endan-
gers their correct functioning.
•
Regularly check the condition of painted and galvanized
parts of the seeder. Avoid leaving residues from chemi-
cal products on the machine.
•
Regularly paint all of the parts for joining and fixing
(rods, screws, nuts, etc…) also inspect that these are well
tight and correctly positioned. Do not use the machine
in the instance where fixtures are not in order or cor-
rectly attached.
•
The sowing machine was mounted with most of the
movements built on auto-lubricant bushings, only the
transmission chains and some pins need to be periodi-
cally greased (distribute a thin layer of grease on the
rollers and on the gear units). In case there is a fertilizer
spreader mounted on the machine, periodically grease
the roller chains and the gear units of the mechanical
operation.
Summary of Contents for Unica Super
