15
14
manufacturer or maintenance department shall be used for replacement
When handling the appliance, we recommend you always use the purpose provided handles recessed
into the sides of the oven to prevent harming people or damaging the appliance itself.
·
This appliance is designed for non-professional ,house-hold use and its functions must not be changed .
·
The electrical system of this appliance can only be used safely when it is correctly connected to an efficient
earthling system in compliance with current safety standards .
·
When the appliance is in use ,the heating elements and some parts of the oven door become
extremely hot .Make sure you don’t touch them and keep children well away.
·
Heat will be generated during its working. Caution must be observed to avoid touch of the heating
element.
The following items are potentially dangerous, and therefore appropriate measures must be taken to
prevent children and the disabled from coming into contact with them:
- Controls and the appliance in general;
- Packaging (bags, polystyrene, nails, etc.);
- The appliance itself, immediately after use of the oven or grill due to the heat generated;
- The appliance itself, when no longer in use (potentially dangerous parts must be made safe).
Avoid the following:
- Touching the appliance with wet parts of the body;
- Using the appliance when barefoot;
- Pulling on the or the supply cable to unplug it from the electrical outlet;
- Improper or dangerous operations;
- Obstructing the ventilation or heat dissipation slots;
- Allowing power supply cables of small appliances to come into contact with the hot parts of the appliance;
- Exposing the appliance to atmospheric agents such as rain, or sunlight;
- Using the oven for storage purposes;
- Using flammable liquids near the appliance;
- Using adapters, multiple sockets and /or extension leads;
- Attempting to install or repair the appliance without the assistance of qualified personnel.
Qualified personnel must be contacted in the following cases:
- Installation (following the manufacturer’s instructions);
- When in doubt about operating the appliance;
- Replacing the electrical socket when it is not compatible with the appliance plug.
- The temperature probe is a part of thermostat, if damaged; they shall be replaced overall by authorized
service person.
Service Centers authorized by the manufacturer must be contacted in the following cases:
- If in doubt about the soundness of the appliance after removing it from its packaging;
- If the power supply cable has been damaged or needs to be replaced;
- If the appliance breaks down or functions poorly; ask for original spare parts.
It is a good idea to do the following:
- Steam cleaner cannot be used to clean the oven;
- Only use the appliance to cook food and nothing else;
- Check the soundness of the appliance after it has been unpacked;
- Disconnect the appliance from the electrical mains if it is not functioning properly and before cleaning or
performing maintenance;
- When left unused, unplug the appliance form the electricity mains;
- Use oven gloves to place cookware in the oven or when removing it;
- Always grip the oven door handle in the center as the extremities of the same may be hot due to any hot air
leaks;
- Make sure the knobs are in the “ ”/“ ”position when the appliance is not in use ;
- Cut the power supply cable after disconnecting it from the mains when you decide not to use the appliance
any longer.
·
The manufacturer may not be held responsible for any damage due to :Incorrect installation, improper, incorrect
and irrational use.
Installation
Only a qualified person in compliance with the instructions provided must install the appliance.
The
manufacturer declines all responsibility for improper installation, which may harm persons and animals and
damage property.
Important:
- The power supply to the appliance must be cut off before any adjustments or maintenance work is
done on it;
- Air duct is supposed to use in Ventilation.
Installation of Built-in Ovens
In order to ensure that the built-in appliance functions properly, the cabinet containing it must be appropriate .The
figure below gives the dimensions of the cut-out for installation under the counter or in a wall cabinet unit.
N. B :Installation in compliance with the consumption declaration
45 mm
．
560
mm
．
In order to ensure adequate ventilation ,the back panel of the cabinet unit must be removed .Installing the oven
so that it rests on two strips of wood is preferable .If the oven rests on a continuous ,flat surface ,there must be an
aperture of at least 45
×
560mm .
The panels of the adjacent cabinets must be made of heat-resistant material .In particular ,cabinets with a veneer
exterior must be assembled with glues which can withstand temperatures of up to 100
℃
.
In compliance with current safety standards, contact with the electrical parts of the oven must not be possible once it has
been installed.
All parts, which ensure the safe operation of the appliance, must be removable only with the aid of a tool.
To fasten the oven to the cabinet, open the door of the oven and attach it by inserting the 4 wooden screws into
the 4 holes located on the perimeter of the frame.
Electrical Connection
N
L
Those ovens equipped with a three-pole power supply cable are designed to operate with an alternating
current .The wire for earthling the appliance is yellow-green in color.
Fitting on a Power Supply Cable
Opening the terminal board:
·
Using a screwdriver ,prize the bolt on the side tabs of the
terminal board cover ;
·
Unscrew the bolt, pull open the cover of the terminal board .
To install the cable, proceed as follows:
·
Remove the wire clamp screw and the three contact screws
L-N -
·
Fasten the wires beneath the screw heads using the following color scheme :
Blue (N) Brown (L)
595
595
565
22
595
565
595
200
MIN
22
200
MIN
45m
in
4
5m
in
4
5m
in
4
5m
in
4
5m
in
5
94
594
545
5
67.
5
21
5
94
594
545
5
67.
5
21
