4 / 29 EN
Refrigerator / User Guide
Important safety and environment instructions
manufacturer, authorised service agent or im-
porter in order to avoid potential dangers.
•
Do not squeeze the power cable under or be-
hind the product. Do not place heavy objects
on the power cable. Power cable must not be
bent excessively, pinched or get in contact with
any heat source.
•
Do not use extension cords, multi-sockets or
adapters to operate the product.
•
Portable multi-sockets or portable power
sources can overheat and cause fire.
Therefore, do not keep any multi-sockets be-
hind or near the product.
•
Plug must be easily accessible. If this is not
possible, the electrical installation to which the
product is connected must contain a device
(such as a fuse, switch, circuit breaker, etc.)
which conforms to the electrical regulations
and disconnects all poles from the grid.
•
Do not touch the power plug with wet hands.
•
Remove the plug from the socket by gripping
the plug and not the cable.
•
When positioning the appliance, ensure the
supply cord is not trapped or damaged
•
Do not locate multiple portable socket-outlets
or portable power supplies at the rear of the
appliance.
1.4 - Transportation safety
•
Product is heavy; do not move it alone.
•
Do not hold its door when moving the product.
•
Pay attention not to damage the cooling sys-
tem or the piping during transportation. If the
piping is damaged, do not operate the product
and call the authorised service agent.
1.5 - Installation safety
•
Call the authorised service agent for installation
of the product. To make the product ready for
use, check the information in the user manual
to make sure that the electricity and water
installations are suitable. If they are not, call a
qualified electrician and plumber to have the
necessary arrangements made. Otherwise,
there is the risk of electric shock, fire, problems
with the product, or injury!
•
Prior to installation, check if the product has
any defects on it. If the product is damaged, do
not have it installed.
•
Place the product on a clean, flat and solid
surface and balance it with adjustable feet.
Otherwise, the product may tip over and cause
injuries.
•
The installation location must be dry and well
ventilated. Do not place carpets, rugs or similar
covers under the product. Insufficient ventila-
tion causes the risk of fire!
•
Do not cover or block the ventilation openings.
Otherwise, power consumption increases and
your product may get damaged.
•
Product must not be connected to supply sys-
tems such as solar power supplies. Otherwise,
your product may get damaged due to sudden
voltage changes!
•
The more refrigerant a refrigerator contains,
the larger the installation location must be. If
the installation location is too small, flammable
refrigerant and air mixture will accumulate in
cases of refrigerant leakage in cooling system.
The required space for each 8 gr of refrigerant
is 1 m³ minimum. The amount of refrigerant in
your product is indicated on the Type Label.
•
Product must not be installed in places ex-
posed to direct sunlight and it must be kept
away from heat sources such as hobs, radia-
tors, etc.
If it is inevitable to install the product close to
a heat source, a suitable insulation plate must
be used in between and the following minimum
distances must be kept to the heat source:
- Minimum 30 cm away from heat sources
such as hobs, ovens, heater units or stoves,
- Minimum 5 cm away from electric ovens.
•
Protection class of your product is Type I.
Plug the product in a grounded socket that
conforms the voltage, current and frequency
values stated on the type label of the product.
The socket must be equipped with a 10 A – 16
A circuit breaker. Our company shall not be li-
able for any damages that will arise when the
product is used without grounding and electri-
cal connection in accordance with the local and
national regulations.
•
Product must not be plugged in during instal-
lation. Otherwise, there is the risk of electric
shock and injury!
