Arcoaire A Series Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 13 / 40

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

1. A filter is required for each return-air inlet. Airflow performance included 3/4-in. (19 mm) washable filter (see accessory list). To determine airflow performance without this filter, assume an

additional 0.1 In. W.C. available external static pressure.

2. Adjust the blower speed tabs as necessary for the proper air temperature rise for each installation.

3. -- Indicates unstable operating conditions.
4. If the same motor speed tap is needed for heating and cooling, a Jumper Wire accessory kit is available. (See Specification sheet for the current Jumper Wire accessory part number). See

Function column for applicable limitations.

A190084

NOTES:

1.Two additional 7/8-in. (22 mm) diameter holes are located in the top plate.

2.Minimum return-air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer’s recommendations for equivalent diameters.

a. For 800 CFM-16-in. (406 mm) round or 14 1/2 x 12-in. (368 x 305 mm) rectangle.

b. For 1200 CFM-20-in. (508 mm) round or 14 1/2 x 19 1/2-in. (368 x 495 mm) rectangle.

c. For 1600 CFM-22-in. (559 mm) round or 14 1/2 x 22 1/16-in. (368 x 560mm) rectangle.

d. For airflow requirements above 1800 CFM, see Air Delivery table in Specification Sheet literature for specific use of single side inlets. The use of both side inlets, a combination of 1

side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.

Fig. 17 – Dimensional Drawing

1102420

Gray

Cooling. Do not use for heating.

2250

2190

2130

2070

2005

1950

1885

1820

1755

1685

Blue

Heating or alt Cooling

1995

1930

1865

1800

1740

1670

1605

1535

1465

1400

Yellow

Alt Cooling or alt Heating

1540

1460

1385

1305

1235

1165

1095

1035

955

890

Orange

Alt Cooling. Do not use for heating.

1345

1195

1135

1055

980

920

845

770

695

620

Red

Alt Cooling. Do not use for heating.

1335

1075

965

890

820

735

660

580

505

440

1352420

Gray

Cooling. Do not use for heating.

2065

2005

1940

1875

1810

1740

1670

1600

1530

1470

Blue

Heating or alt Cooling

1825

1760

1695

1630

1560

1490

1420

1350

1275

1205

Yellow

Alt Cooling or alt Heating

1760

1690

1625

1555

1485

1415

1345

1275

1200

1130

Orange

Alt Cooling. Do not use for heating.

1620

1550

1480

1405

1335

1260

1195

1130

1065

995

Red

Alt Cooling. Do not use for heating.

1325

1260

1185

1100

1025

955

885

805

735

670

1552420

Gray

Cooling. Do not use for heating.

2205

2150

2090

2030

1965

1905

1840

1780

1710

1645

Blue

Heating or alt Cooling

2055

1995

1935

1875

1810

1750

1690

1615

1540

1460

Yellow

Alt Cooling or alt Heating

1860

1795

1730

1670

1605

1540

1470

1395

1320

1250

Orange

Alt Cooling. Do not use for heating.

1495

1430

1355

1285

1210

1130

1065

995

930

850

Red

Alt Cooling. Do not use for heating.

1295

1085

1000

910

835

765

670

600

530

465

Table 4 – Air Delivery - CFM (With Filter)* (Continued)

Furnace

Wire Lead

Color

Function

Test Airflow Delivery @ Various External Static Pressures

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

33 1/3

[845.9]

Summary of Contents for A Series









































Search results

Summary of Contents for A Series

Reviews:

Related manuals for A Series

Brands by name

Popular brands

Arcoaire A Series, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for A Series

Reviews:

Related manuals for A Series

Brands by name

Popular brands