background image

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

17

A190079

Fig. 24 – Heating and Cooling Application Wiring Diagram with 1-Stage Thermostat

\

A190279

Fig. 25 – Field-Supplied External Electrical Box on Furnace Casing

* Permissible limits of the voltage range at which the unit operates satisfactorily.

# Unit ampacity = 125 percent of largest operating component’s full load amps plus 100 percent of all other potential operating components’ (EAC, humidifier, etc.) full load amps.

 Time-delay type is recommended.

 Length shown is as measured one way along wire path between unit and service panel for maximum 2 percent voltage drop.

115-V FIELD-

SUPPLIED

DISCONNECT

AUXILIARY
J-BOX

24-V

TERMINAL

BLOCK

THREE-WIRE

HEATING-ONLY

FIVE WIRE

NOTE 1

NOTE 2

FIELD-SUPPLIED
DISCONNECT

CONDENSING
UNIT

TWO
WIRE

FURNACE

C
O
N

T

R
O

L

R

G

COM

W

C

R

G

Y

GND

GND

FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING

208/230- OR
460-V
THREE
PHASE

208/230-V
SINGLE
PHASE

BLOWER DOOR SWITCH

WHT

BLK

WHT

BLK

NOTES:

Connect Y-terminal in furnace as shown for proper blower operation.
Some thermostats require a "C" terminal connection as shown.
If any of the original wire, as supplied, must be replaced, use
same type or equivalent wire.

W

   Y

GND

THERMOSTAT
TERMINALS

1.
2.
3.

WARNING

!

FIRE HAZARD

Failure to follow this warning could result in personal injury, death, or

property damage. 

Do not connect aluminum wire between disconnect switch and furnace.

Use only copper wire (see 

Fig. 25

).

COPPER

WIRE ONLY

ELECTRIC

DISCONNECT

SWITCH

ALUMINUM

WIRE

Table 7 – Electrical Data

Unit Size

Volts-

Hertz- Phase

Operating Voltage* Range

Unit

Ampacity#

Minimum Wire

 Size AWG

Maximum Wire

Length

Maximum 

Fuse

 or CKT 

BKR Amps

Maximum

Minimum

feet

m

0451412

115-60-1

127

104

7.8

14

47

14.3

15

0451712

115-60-1

127

104

10.3

14

36

11

15

0701412

115-60-1

127

104

7.8

14

47

14.3

15

0701712

115-60-1

127

104

7.8

14

47

14.3

15

0701716

115-60-1

127

104

14.3

14

25

7.6

15

0702116

115-60-1

127

104

13.3

14

27

8.2

15

0901714

115-60-1

127

104

11

14

33

10.1

15

0902116

115-60-1

127

104

11

14

33

10.1

15

0902120

115-60-1

127

104

16.9

12

34

10.4

20

0902420

115-60-1

127

104

13.5

14

27

8.2

15

1102120

115-60-1

127

104

17.4

12

33

10.1

20

1102420

115-60-1

127

104

14

14

26

7.9

15

1352420

115-60-1

127

104

14

14

26

7.9

15

1552420

115-60-1

127

104

14

14

26

7.9

15

Summary of Contents for A Series









































Reviews: