Arcoaire C9MPD Installation Instruction Download

Page: 9 / 70

440 01 1024 01

Specifications are subject to change without notice

If the furnace is to be installed in a crawl space, consult local

codes. A suitable concrete pad or blocks are recommended for

crawl space installation on the ground.
NOTE: 6

″

bottom clearance required for condensate trap.

″

between the front of the furnace and adjacent construction or

other appliances

MUST

be maintained for service clearance.

Keep all insulating materials clear from louvered door. Insulating

materials may be combustible.

The horizontal furnaces may be installed directly on combustible

wood flooring or supports as long as all required furnace

clearances are met. See

Figure 5.

This furnace

MUST NOT

be installed directly on carpeting or tile or

other combustible material other than wood flooring or supports.
For horizontal installation over a finished living space. A field

fabricated auxiliary drain pan with drain pipe is required to prevent

damage by overflow due to blocked condensate drain.

3. Combustion & Ventilation Air

For Single Pipe Installation

CARBON MONOXIDE POISONING HAZARD.
Failure to follow this warning could result in

personal injury or death.
Use methods described here to provide

combustion and ventilation air.

WARNING

Furnaces require ventilation openings to provide sufficient air for

proper combustion and ventilation of flue gases. All duct or

openings for supplying combustion and ventilation air must

comply with the gas codes, or in the absence of local codes, the

applicable national codes.
Combustion and ventilation air must be supplied in accordance

with one of the following:
Note: The Combustion & Ventilation Air Section in this document,

uses tables and information from the ANSI Z223.1/NFPA

54. For use in Canada, use CSA B149.1 for this information.

1. Section 9.3, Air for Combustion and Ventilation, of the National

Fuel Gas Code, (NFGC), ANSI Z223.1--2006/NFPA 54--2006

in the U.S.,

2. Sections 8.2, 8.3, 8.5, 8.6, 8.7, and 8.8 of National Standard of

Canada, Natural Gas and Propane Installation Code

(NSCNGPIC), CSA B149.1--05 in Canada,

3. Applicable provisions of the local building code.
This furnace can NOT be common vented or connected to any

type B, BW or L vent or vent connector, nor to any portion of a

factory--built or masonry chimney. Multistory venting is NOT

permitted. If this furnace is replacing a previously common-vented

furnace, it may be necessary to resize the existing vent and

chimney to prevent oversizing problems for the other remaining

appliance(s). See

“Venting and Combustion Air Check”

in this

section

This furnace MUST be vented to the outside.

When the installation is complete, check that all appliances have

adequate combustion air and are venting properly. See

Venting

And Combustion Air Check

in “

Gas Vent Installation”

Section in

this manual.

Outdoor Combustion Air Method

A space having less than 50 cubic feet per 1,000 BTUH input rating

for all gas appliances installed in the space requires outdoor air for

combustion and ventilation.

Air Openings and Connecting Ducts

1. Total input rating for all gas appliances in the space

MUST

considered when determining free area of openings.

2. Connect ducts or openings directly to the outdoors.
3. When screens are used to cover openings, the openings

MUST

be no smaller than

″

mesh.

4. The minimum dimension of air ducts

MUST NOT

be less than

″

5. When sizing a grille, louver, or screen use the free area of

opening. If free area is

NOT

stamped or marked on grill or

louver, assume a 20% free area for wood and 60% for metal.

Screens shall have a mesh size not smaller than

″

Requirements

1. Provide the space with sufficient air for proper combustion and

ventilation of flue gases using horizontal or vertical ducts or

openings.

Figure 6

illustrates how to provide combustion and ventilation

air when two permanent openings, one inlet and one outlet, are

used.

a. One opening

MUST

commence within 12

″

of the floor

and the second opening

MUST

commence within 12

″

the ceiling.

b. Size openings and ducts per

Table 1

Summary of Contents for C9MPD







































































Search results

Summary of Contents for C9MPD

Reviews:

Related manuals for C9MPD

Brands by name

Popular brands

Arcoaire C9MPD, Installation Instruction

Search results

Summary of Contents for C9MPD

Reviews:

Related manuals for C9MPD

Brands by name

Popular brands