Arcteq AQ-G215 Instruction Manual Download

Page: 35 / 458

Figure. 4.5 - 31. Digital input section.

All settings related to digital inputs can be found in the "Digital inputs" section.

The "Digital inputs settings" subsection includes various settings for the inputs: the polarity selection

determines whether the input is Normal Open (NO) or Normal Closed (NC) as well as the activation

threshold voltage (16…200 V AC/DC, step 0.1 V) and release threshold voltage (10…200 V AC/DC,

step 0.1 V) for each available input. There is also a setting to determine the wanted activation and

release delay (0…1800 s, step 1 ms). Digital input activation and release threshold follow the

measured peak value. The activation time of an input is 5…10 ms. The release time with DC is 5…10

ms, while with AC it is less than 25 ms. The first three digital inputs don't have activation and release

threshold voltage settings as these have already been defined when the unit was ordered.

Digital input statuses can be checked from the corresponding subsection ("Digital input status"). The

"Digital input descriptions" subsection displays the texts the user has written for each digital input. In

the "Event masks" subsection you can determine which events are masked –and therefore recorded

into the event history– and which are not.

Figure. 4.5 - 32. Digital outputs section.

All settings related to digital outputs can be found in the "Digital outputs" section.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands