Arcteq AQ-G215 Instruction Manual Download

Page: 52 / 458

• Super user (***)
• Configurator (**)
• Operator (*)
• User ( - )

You can set a new password for a user level by selecting the key icon next to the user level's name.

After this you can lock the user level by pressing the R

Reetturn

urn key while the lock is selected. If you need

to change the password, you can select the key icon again and give a new password. Please note that

in order to do this the user level whose password is being changed must be unlocked.

As mentioned above, the access level of the different user levels is indicated by the number of stars.

The required access level to change a parameter is indicated with a star (*) symbol if such is required.

As a general rule the access levels are divided as follows:

•

User: Can view any menus and settings but cannot change any settings, nor operate

breakers or other equipment.

•

Operator: Can view any menus and settings but cannot change any settings BUT can

operate breakers and other equipment.

Q-G215

-G215

Instruction manual

Version: 2.04

Summary of Contents for AQ-G215










































































































































































































































































































































































































































































Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands

Arcteq AQ-G215, Instruction Manual

Search results

Summary of Contents for AQ-G215

Reviews:

Related manuals for AQ-G215

Brands by name

Popular brands