background image

 

 

Galvanized Gas Spreader 

Page 3 

www.arcticsnowplows.com 

 

 

 

 

- Liability for damage to the property, or injury to, or death of any person arising out of the 

operation, maintenance or use of the covered product. 

This warranty is made only to the original purchaser. There is no other warranty 

expressed, implied, or statutory. 

 

The customer must register the equipment with Arctic within 60 days from the day of purchase 

using the online registration system found on the Arctic Equipment website 

www.arcticsnowplows.com/warranty

 

 

All parts returned to us, transportation charges prepaid, must be accompanied with a 

"Return Goods Authorization" number, obtained from the factory. In order to reduce 

down-time, we will, on your request, send the parts required and you will be billed under 

the usual terms. A credit will be issued to your account when the parts, in our 

examination, prove to be defective. 

 

Arctic Equipment Manufacturing Corporation reserves the right to change specification 

without prior notice. 

Customer Responsibility 

 

The loaded vehicle, including all after market accessories, the salt/sanding equipment, 

passengers, and cargo, MUST NOT exceed the gross vehicle weight rating (GAWR), 

front gross axle weight rating (FGAWR), or rear gross axle weight rating (RGAWR) 

specified on the Safety Compliance Certification Label located in the driver’s side door 

opening. It is the operator’s responsibility to verify that these ratings are not 

exceeded. 

To determine the Gross Axle Weights for your vehicle, including all after market 

accessories, the salt/sanding equipment, passengers, and cargo, take your loaded vehicle 

to a scale. Place the front wheels of the vehicle on the scale to get the Front Gross Axle 

Weights (FGAW). To get the Rear Gross Axle Weights (RGAW), place the back wheels 

of the vehicle on the scale. 

Disclaimer Notice 

Arctic Equipment Manufacturing Corporation (Arctic) does not assume liability for damage 

to your motor vehicle resulting from the attachment or use of an Arctic salt/sanding 

equipment. The purchaser assumes all vehicle risk associated with the attachment and 

operation of this salt/sanding equipment. 

The added weight may impair the operation and control of your vehicle. Additional 

equipment may be necessary before installing salt/sanding equipment. Please consult 

your vehicle dealers prior to the purchase and installation of the salt/sanding equipment. 

 

 

 

Summary of Contents for AG10

























Reviews: