background image

GM055PO26641106

P.9

Important Safety Precautions

# First time flyer should never fly by himself / herself.  Assistance from experienced flyer
   is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
   pre-adjusted aircraft.

#                            is specially designed to be powered by 

KM0374810 Outrunner Motor.

 

# Make sure the air field is spacious, never fly the plane too close to people and never get 
   too close to a running propeller.  Extreme caution should be exercised when working with 
   electric powered models.  Make sure the propeller is cleared of all objects, especially your 
   hands before connecting the battery to the model.  Make sure you understand the 
   operation of the ESC (Electronic Speed Control) by studying the ESC manual.  Once you 
   plug in the battery for electric powered model, always treat the propeller as a rotating one, 
   as accidental movement of the throttle stick will spin the propeller and could cause injuries.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

Warning!

HandyKing EP(40)

C.G.

13

The ideal C.G. position is 130mm (5.1 in.) behind the leading edge 
measured at where the wing meets the fuselage.  In order to obtain 
the C.G. specified, add weight to the fuselage or move the battery 
position.  Check the C.G. before flying. 

130mm

5.1 in.

C.G.

http://www.thewingsmaker.com/instructionManuals.php

Summary of Contents for HandyKing EP













Reviews: