Ariel ARL-701, Installation & User Manual

After Installation:

41.

Before

supplying

any

power

to

the

product,

you

should

inspect

the

power

cables

to

ensure

the

power

leads

are

properly

connected.

42.

After

installation

and

before

starting

the

product

for

the

first

time,

you

should

inspection

all

the

connections

to

ensure

they

are

properly

connected;

including

parts,

plugs,

hoses,

nuts,

screws,

wires,

etc.

43.

After

you

have

fully

installed

the

unit

and

made

all

the

inspections

to

ensure

the

unit

can

function

safely, fully

clean

the

unit

inside

and

out

to

ensure

the

unit

is

ready

for

usage,

and

also

to

check

for

any

potential

lose

debris

that

may

have

fallen

into

any

of

the

plumbing.

After

a

thorough

visual

inspection,

close

the

drain

and

fill

the

tub

up

to

the

overflow

drain,

submerging

all

the

jets

underwater.

If

any

debris

floats

out,

remove

it.

44.

The

whirlpool

system

will

not

run

unless

the

water-level

sensor

is

fully

submerged

underwater.

The

water-level

sensor

is

placed

above

the

water

line

of

the

water

jets.

45.

Turn-on

the

whirlpool

system

and

operate

it

for

a

minimum

of

10-minutes.

Then

turn-off

the

whirlpool

system

and

without

draining

it,

allow

it

to

sit

for

a

minimum

of

10-minutes.

Now

check

all

the

plumbing,

pipe

works,

hoses,

joints,

threads

and

any

other

connections

for

any

leaks.

If

there

are

any

adjustments

made,

restart

this

test

and

review

all

the

connections

again.

46.

You

must

ensure

the

product

works

as

it

normally

would:

immediately

test

all

functions

of

the

product

to

possibly

find

any

errors.

After

testing,

place

the

tub

against

the

wall(s)

and

seal

the

wall

joints

with

an

acid-free

caulking

agent

and

then

allow

it

to

cure

sufficiently

before

any

further

use.

Additional Precautions:

47.

It

is

not

generally

recommended

to

use

bath

oils

in

whirlpool

bathtubs,

as

the

oil

residue

can

stick

to

the

side

walls

of

the

tub

and

plumbing.

Clean

the

whirlpool

system

after

any

such

uses.

48.

It

is

not

recommended

to

use

coarse

grain

bath

salts

with

the

whirlpool

function,

as

it

may

enter

the

water

pump

and

damage

or

cause

additional

wear

onto

its

internal

components.

6

13

Maintenance:

Recommended cleaning the whirlpool features monthly with a whirlpool clean-

ing solution from your local hardware store. Follow the instructions of the

whirlpool cleaning solution. If not cleaned regularly you may notice black

flakes 

in the bath – if this happens you should clean the whirlpool system.

Consider cleaning the whirlpool system with whirlpool cleaning solution re-

peatedly until the black flakes disappear. Soap scum, hair, dead skin, skin

care 

products, oil, grease and/or bacteria can contaminate your whirlpool sys-tem, it 

is important

to clean regularly.

Consider cleaning the whirlpool system using a cup of chlorine bleach (

sodium 

hypochlorite

)

and the minimum amount of warm or hot water to activate the

(water-level sensor) whirlpool system, in between regular cleanings with

whirlpool cleaning solution. Thoroughly flush and rinse the bathtub and

whirlpool system before use. (This is not meant as a substitute for whirlpool

cleaning solution)

The drain can be clogged by hair or soap scum and should be cleaned regu-

larly. Cleaning schedule is based off usage conditions; monitor time frame for

any slowing of drainage, and then set cleaning schedule.

Poor maintenance, infrequent, or irregular cleaning can cause damage to the

faucets or jets. Cleaning schedule is based off usage conditions; generally,

more frequent light cleanings are better than less frequent, heavy cleanings.

When cleaning the chrome parts, do not use cleaning compounds or instru-

ments with abrasives or harsh chemicals. Do not try to remove stains with

hard 

objects, such as blades or screwdrivers.

When cleaning the acrylic surfaces of the bathtub, use a soft sponge and a

detergent without ammonia, acetone or other harsh chemicals, to prevent sur-

faces from getting dulled or damaged.

Dulled surfaces can be refinished with an acrylic polishing compound (follow

instructions of polishing compound); first spot test in a non-visible surface

area.

Warning:

 The use of cleaning materials other than those recommended by

the 

manufacturer can result in damage to the bathtub, whirlpool apparatus, or

other hardware. Spot test in non-visible area.

Warning:

 Any service, adjustment or repair is only recommended by an expe-

rienced professional. Only consider a licensed professional for all installation,

servicing or repair work.